Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for 17-4 PH (X5CrNiCuNb16-4). The numbers are the published M30 PH stainless (17-4PH) sub-group starting band; the designations are on the cross-reference page.
| Item | Value |
|---|---|
| ISO 513 group | M Stainless steel |
| Sub-group | M30 PH stainless (17-4PH) |
| Sub-group hardness / condition | 28–44 HRC |
| Category | Precipitation-hardening stainless |
| EN / Werkstoffnummer | X5CrNiCuNb16-4 · 1.4542 |
Hardness is the range published for the whole M30 PH stainless (17-4PH) sub-group on our material guide; the delivery condition of your 17-4 PH may sit anywhere inside it or outside it.
| Condition | Vc m/min | Vc sfm | Feed mm/rev | Feed ipr |
|---|---|---|---|---|
| Solution annealed | 100–160 | 330–525 | 0.10–0.25 | .004–.010 |
| Aged (H900) | 80–120 | 260–395 | 0.10–0.25 | .004–.010 |
Sub-group starting values for carbide inserts, from M30 PH stainless (17-4PH). They describe the whole sub-group and are not tuned to 17-4 PH. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO M group range.
| Operation | Geometry | Coating family | Coolant | First check |
|---|---|---|---|---|
| Roughing | Positive honed edge, rigid setup | PVD-coated M-class carbide; harder, more wear-resistant grade for aged H900 / H1025 | High-pressure coolant | Heat-treat condition: annealed versus aged drives grade and speed |
| Finishing | Positive honed edge | PVD-coated M-class carbide | High-pressure coolant | Built-up edge: raise Vc into the band, coolant at the edge |
| Interrupted cut | Positive honed edge, rigid setup | Tougher PVD-coated carbide | High-pressure coolant | Edge chipping on aged material |
| Low rigidity / thin wall | Positive honed edge; rigid setup, short overhang | PVD-coated M-class carbide | High-pressure coolant | Work-hardening: keep DOC above the hardened layer, never dwell |
Setup rows are the selection table of the M30 PH stainless (17-4PH) guide. They carry no speeds, so they do not change the starting band above.
One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
Scope: Catalogue group M1.1.3 is heat-treated ferritic/martensitic stainless at 240 HB. Common 17-4PH conditions are harder (H1150 roughly 28-33 HRC, H900 about 44 HRC), so treat these values as the softest case, not as data for your condition.
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 15 / 0.051 | - | - | - | - | - | - | 398 |
| Art. 2469 coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 35 / 0.035 | 35 / 0.055 | 35 / 0.07 | 35 / 0.08 | 35 / 0.095 | 35 / 0.115 | 35 / 0.14 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 35 / 0.035 | 35 / 0.055 | 35 / 0.07 | 35 / 0.08 | 35 / 0.095 | 35 / 0.115 | 35 / 0.14 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 40 / 0.035 | 40 / 0.055 | 40 / 0.07 | 40 / 0.08 | 40 / 0.095 | 40 / 0.115 | 40 / 0.14 | 404 |
| Art. 2477 coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 35 / 0.035 | 35 / 0.055 | 35 / 0.07 | 35 / 0.08 | 35 / 0.095 | 35 / 0.115 | 35 / 0.14 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 40 / 0.035 | 40 / 0.055 | 40 / 0.07 | 40 / 0.08 | 40 / 0.095 | 40 / 0.115 | 40 / 0.14 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 40 / 0.035 | 40 / 0.055 | 40 / 0.07 | 40 / 0.08 | 40 / 0.095 | 40 / 0.115 | 40 / 0.14 | 404 |
| Art. 4044 coating FIRE | yes | 50 / 0.05 | 50 / 0.09 | 50 / 0.11 | 50 / 0.13 | 50 / 0.15 | 50 / 0.185 | 50 / 0.22 | 408 |
| Art. 4045 coating FIRE | yes | 50 / 0.05 | 50 / 0.09 | 50 / 0.11 | 50 / 0.13 | 50 / 0.15 | 50 / 0.185 | 50 / 0.22 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | 70 / 0.235 | 70 / 0.275 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 60 / 0.065 | 60 / 0.11 | 60 / 0.14 | 60 / 0.165 | 60 / 0.185 | 60 / 0.235 | 60 / 0.275 | 413 |
| Art. 5525 coating FIRE | yes | 50 / 0.05 | 50 / 0.09 | 50 / 0.11 | 50 / 0.13 | 50 / 0.15 | 50 / 0.185 | 50 / 0.22 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 40 / 0.035 | 40 / 0.055 | 40 / 0.07 | 40 / 0.08 | 40 / 0.095 | 40 / 0.115 | 40 / 0.14 | 404 |
| Art. 6023 coating FIRE | yes | 50 / 0.065 | 50 / 0.11 | 50 / 0.14 | 50 / 0.165 | 50 / 0.185 | 50 / 0.235 | 50 / 0.275 | 406 |
| Art. 6025 coating TiAlN nanoA | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | 70 / 0.235 | 70 / 0.275 | 414 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 35 / 0.035 | 35 / 0.055 | 35 / 0.07 | 35 / 0.08 | 35 / 0.095 | 35 / 0.115 | 35 / 0.14 | 403 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 60 / 0.056 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 25 / 0.056 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 60 / 0.056 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 60 / 0.056 | - | - | - | - | - | - | 393 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 35 / 0.064 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 85 / 0.095 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 85 / 0.095 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 85 / 0.095 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 85 / 0.095 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 70 / 0.051 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | 70 / 0.235 | 70 / 0.275 | 412 |
| Art. 6499 coating FIRE | yes | 60 / 0.065 | 60 / 0.11 | 60 / 0.14 | 60 / 0.165 | 60 / 0.185 | 60 / 0.235 | 60 / 0.275 | 413 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 85 / 0.065 | 85 / 0.11 | 85 / 0.14 | 85 / 0.165 | 85 / 0.185 | 85 / 0.235 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 85 / 0.065 | 85 / 0.11 | 85 / 0.14 | 85 / 0.165 | 85 / 0.185 | 85 / 0.235 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 85 / 0.065 | 85 / 0.11 | 85 / 0.14 | 85 / 0.165 | 85 / 0.185 | 85 / 0.235 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 40 / 0.04 | 40 / 0.07 | 40 / 0.085 | 40 / 0.105 | 40 / 0.12 | 40 / 0.145 | 40 / 0.175 | 402 |
| Art. 8511 coating TiAlN nanoA | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | 70 / 0.235 | 70 / 0.275 | 414 |
| Art. 8611 coating TiAlN nanoA | yes | 70 / 0.065 | 70 / 0.11 | 70 / 0.14 | 70 / 0.165 | 70 / 0.185 | 70 / 0.235 | 70 / 0.275 | 414 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 414, 426, 427, 428, 429, 430).
Values are for the catalogue material group(s) shown, which cover the M30 PH stainless (17-4PH) sub-group; they are not tuned to 17-4 PH. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
Scope: Catalogue group M1.1.3 is heat-treated ferritic/martensitic stainless at 240 HB. Common 17-4PH conditions are harder (H1150 roughly 28-33 HRC, H900 about 44 HRC), so treat these values as the softest case, not as data for your condition.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | Plunging | 85 | 1xD | 1xD | 0.01 | 0.02 | 0.025 | 0.03 | 0.035 | 0.05 | 0.06 | 0.06 |
| M1.1.3 | Slotting | 85 | 1xD | 1xD | 0.015 | 0.02 | 0.03 | 0.04 | 0.05 | 0.065 | 0.08 | 0.08 |
| M1.1.3 | Roughing | 125 | 1.5xD | 0.33xD | 0.02 | 0.03 | 0.04 | 0.055 | 0.065 | 0.085 | 0.105 | 0.105 |
| M1.1.3 | Finishing | 165 | 2xD | 0.02xD | 0.02 | 0.025 | 0.035 | 0.045 | 0.055 | 0.07 | 0.09 | 0.09 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | HPC Roughing | Speed M | 135 | 3xD | 0.1xD | 0.035 | 0.055 | 0.07 | 0.09 | 0.105 | 0.14 | 0.18 | 0.18 |
| M1.1.3 | HSC Roughing | Speed M | 140 | 3xD | 0.08xD | 0.04 | 0.06 | 0.075 | 0.095 | 0.115 | 0.155 | 0.195 | 0.195 |
| M1.1.3 | Finishing | Speed M | 140 | 3xD | 0.02xD | 0.015 | 0.02 | 0.03 | 0.035 | 0.045 | 0.06 | 0.07 | 0.07 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | Slotting | 150 | see ap table | 1xD | 0.028 | 0.056 | 0.084 | 0.11 | 0.165 | 0.225 | 0.315 | 0.38 | 0.505 |
| M1.1.3 | Roughing | 145 | see ap table | 0.4xD | 0.04 | 0.079 | 0.119 | 0.16 | 0.235 | 0.315 | 0.395 | 0.475 | 0.635 |
| M1.1.3 | (Pre-)Finishing | 150 | see ap table | 0.3xD | 0.032 | 0.063 | 0.095 | 0.125 | 0.19 | 0.255 | 0.315 | 0.38 | 0.505 |
ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:
| Material | Hardness | Ø 1 | Ø 2 | Ø 3 | Ø 4 | Ø 6 | Ø 8 | Ø 10 | Ø 12 | Ø 16 |
|---|---|---|---|---|---|---|---|---|---|---|
| P | less than 850 N/mm² | 0.06 | 0.12 | 0.18 | 0.24 | 0.36 | 0.48 | 0.6 | 0.72 | 0.96 |
| P | more than 850 N/mm² | 0.05 | 0.1 | 0.15 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.8 |
| M | less than 850 N/mm² | 0.04 | 0.08 | 0.12 | 0.16 | 0.24 | 0.32 | 0.4 | 0.48 | 0.64 |
| M | more than 850 N/mm² | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
| K | less than 240 HB | 0.06 | 0.12 | 0.18 | 0.24 | 0.36 | 0.48 | 0.6 | 0.72 | 0.96 |
| K | more than 240 HB | 0.05 | 0.1 | 0.15 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.8 |
| S | Ti alloys | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
| H | less than 55 HRC | 0.04 | 0.08 | 0.12 | 0.16 | 0.24 | 0.32 | 0.4 | 0.48 | 0.64 |
| H | 55-65 HRC | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | Roughing | 150 | 0.1xD | 0.3xD | 0.008 | 0.016 | 0.032 | 0.048 | 0.065 | 0.095 | 0.125 | 0.16 | 0.19 |
| M1.1.3 | (Pre-)Finishing | 145 | 0.05xD | 0.1xD | 0.01 | 0.02 | 0.039 | 0.059 | 0.08 | 0.115 | 0.155 | 0.195 | 0.235 |
| M1.1.3 | Fine finishing | 150 | 0.01xD | 0.02xD | 0.009 | 0.017 | 0.034 | 0.051 | 0.07 | 0.105 | 0.135 | 0.17 | 0.205 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | Roughing | 100 | 0.05xD | 0.4xD | 0.007 | 0.013 | 0.026 | 0.04 | 0.055 | 0.08 | 0.105 | 0.13 | 0.16 |
| M1.1.3 | (Pre-)Finishing | 105 | 0.03xD | 0.25xD | 0.005 | 0.011 | 0.021 | 0.032 | 0.04 | 0.065 | 0.085 | 0.105 | 0.125 |
| M1.1.3 | Fine finishing | 110 | 0.01xD | 0.15xD | 0.006 | 0.012 | 0.023 | 0.035 | 0.045 | 0.07 | 0.095 | 0.115 | 0.14 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3 | Roughing | 165 | 0.1xD | 0.1xD | 0.004 | 0.008 | 0.024 | 0.045 | 0.065 | 0.08 | 0.095 | 0.125 | 0.16 |
| M1.1.3 | (Pre-)Finishing | 130 | 0.03xD | 0.03xD | 0.002 | 0.005 | 0.014 | 0.03 | 0.04 | 0.05 | 0.06 | 0.075 | 0.095 |
| M1.1.3 | Fine finishing | 130 | 0.01xD | 0.01xD | 0.001 | 0.003 | 0.008 | 0.015 | 0.02 | 0.03 | 0.035 | 0.045 | 0.055 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Values are for the catalogue material group(s) shown, which cover the M30 PH stainless (17-4PH) sub-group; they are not tuned to 17-4 PH.
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
Scope: Catalogue group M1.1.3 is heat-treated ferritic/martensitic stainless at 240 HB. Common 17-4PH conditions are harder (H1150 roughly 28-33 HRC, H900 about 44 HRC), so treat these values as the softest case, not as data for your condition.
| Material group | Vc (m/min) | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 62 | 0.1 | 0.2 | 0.25 | 0.45 | 0.6 | 0.7 | 0.75 | 0.8 | 0.85 | 0.95 |
f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.
| Material group | Vc (m/min) | f Ø 14 | f Ø 16 | f Ø 18 | f Ø 20 | f Ø 22 | f Ø 24 | f Ø 28 | f Ø 32 | f Ø 38 | f Ø 42 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 62 | 0.8 | 0.85 | 0.9 | 0.95 | 1 | 1 | 1.1 | 1.15 | 1.25 | 1.3 |
f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.
| Material group | Vc (m/min) | f Ø 22 | f Ø 26 | f Ø 30 | f Ø 35 | f Ø 40 |
|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 31 | 1 | 1.05 | 1.1 | 1.2 | 1.25 |
f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.
| Material group | Vc (m/min) | f Ø 40 | f Ø 45 | f Ø 50 | f Ø 55 | f Ø 60 | f Ø 65 | f Ø 70 | f Ø 75 | f Ø 80 |
|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 31 | 1.25 | 1.3 | 1.35 | 1.45 | 1.5 | 1.55 | 1.6 | 1.6 | 1.65 |
f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 6 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 9 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 6 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 6 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| M1.1.3: Stainless steel, ferritic/martensitic, heat-treated, Rm 810 N/mm², 240 HB | 6 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
Values are for the catalogue material group(s) shown, which cover the M30 PH stainless (17-4PH) sub-group; they are not tuned to 17-4 PH.
PVD-coated M-class carbide for solution-annealed 17-4PH (~28–33 HRC). For aged H900 / H1025 (~40–44 HRC), use a harder, more wear-resistant grade and lower the speed.
The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO M grade list and in the grade chart.
EN X5CrNiCuNb16-4, Werkstoffnummer 1.4542, US AISI 630 (UNS S17400), JIS SUS630. The full table, with the nearest-match flags, is on the 17-4 PH / 1.4542 cross-reference page.
Condition decides everything: solution-annealed it cuts like a tough martensitic, H900 it fights back hard. Machine before ageing where the drawing allows.
Are you overpaying on your 17-4 PH inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
The published starting band for the M30 PH stainless (17-4PH) sub-group is Solution annealed 100–160 m/min (330–525 sfm) at 0.10–0.25 mm/rev (.004–.010 ipr); Aged (H900) 80–120 m/min (260–395 sfm) at 0.10–0.25 mm/rev (.004–.010 ipr). It is a starting band for the whole sub-group, not a value tuned to 17-4 PH, so confirm on a sample part and adjust for condition, tool and rigidity.
PVD-coated M-class carbide for solution-annealed 17-4PH (~28–33 HRC). For aged H900 / H1025 (~40–44 HRC), use a harder, more wear-resistant grade and lower the speed. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.
EN X5CrNiCuNb16-4 (Werkstoffnummer 1.4542); US: AISI 630 (UNS S17400); JIS: SUS630. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.
The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.