CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · M AUSTENITIC STAINLESS (FREE-CUTTING)

AISI 303 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for AISI 303 (X8CrNiS18-9). The numbers are the published M01 Austenitic (304, 316L) sub-group starting band; the designations are on the cross-reference page.

ISO M · Stainless steel M01 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

AISI 303: group, sub-group and condition

ItemValue
ISO 513 groupM Stainless steel
Sub-groupM01 Austenitic (304, 316L)
Sub-group hardness / condition150–220 HB
CategoryAustenitic stainless (free-cutting)
EN / WerkstoffnummerX8CrNiS18-9 · 1.4305

Hardness is the range published for the whole M01 Austenitic (304, 316L) sub-group on our material guide; the delivery condition of your AISI 303 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for AISI 303

ConditionVc m/minVc sfmFeed mm/revFeed ipr
M01 Austenitic (304, 316L), 150–220 HB120–200395–6550.10–0.35.004–.014

Sub-group starting values for carbide inserts, from M01 Austenitic (304, 316L). They describe the whole sub-group and are not tuned to AISI 303. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO M group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingPositive rake, lightly honed edge, open polished chipbreaker; avoid a heavy negative landTough PVD-coated carbideHigh-pressure coolant 15–20 bar aimed at the edgeConsistent depth of cut: stay above the work-hardened layer
FinishingPositive rake, sharp edge, polished chipbreakerPVD-coated carbide, sharper edgeHigh-pressure coolant 15–20 barBuilt-up edge: Vc too low or tool dwelling
Interrupted cutPositive but robust honed edgeTougher PVD-coated carbideHigh-pressure coolant 15–20 barNotch wear at the depth-of-cut line: vary DOC between passes
Low rigidity / thin wallPositive rake, sharp edge to avoid pushing the materialPVD-coated carbideHigh-pressure coolant 15–20 barFeed high enough for the chipbreaker to engage

Setup rows are the selection table of the M01 Austenitic (304, 316L) guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: AISI 304 · AISI 304L · AISI 316 · AISI 316L · AISI 316Ti · AISI 321

02b · DRILLING

Drilling AISI 303 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

M2.1.1: Stainless steel, austenitic, quenched, 180 HB (37 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no15 / 0.045------398
Art. 2469
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165406
Art. 2471
Solid carbide drills, coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13403
Art. 2474
Solid carbide drills, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13404
Art. 2477
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165406
Art. 2479
Solid carbide drills, coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13403
Art. 2719
Solid carbide drills, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13404
Art. 2996
Solid carbide drills, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13404
Art. 4044
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165408
Art. 4045
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165408
Art. 5525
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165407
Art. 5651
Solid carbide drills, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13404
Art. 6023
coating FIRE
yes55 / 0.0455 / 0.06555 / 0.0855 / 0.09555 / 0.1155 / 0.13555 / 0.165406
Art. 6025
coating TiAlN nanoA
yes60 / 0.0660 / 0.10560 / 0.1360 / 0.15560 / 0.17560 / 0.2260 / 0.26414
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0325 / 0.0525 / 0.06525 / 0.07525 / 0.0925 / 0.1125 / 0.13403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes60 / 0.036------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no15 / 0.036------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes60 / 0.045------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes60 / 0.045------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no25 / 0.045------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes80 / 0.09------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes80 / 0.09------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes80 / 0.09------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes80 / 0.09------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes80 / 0.06------397
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes70 / 0.0570 / 0.0870 / 0.170 / 0.1270 / 0.1470 / 0.175-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes60 / 0.0560 / 0.0860 / 0.160 / 0.1260 / 0.1460 / 0.175-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes60 / 0.0560 / 0.0860 / 0.160 / 0.1260 / 0.1460 / 0.175-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes60 / 0.0560 / 0.0860 / 0.160 / 0.1260 / 0.14--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes60 / 0.0460 / 0.06560 / 0.0860 / 0.095---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes40 / 0.0540 / 0.0840 / 0.140 / 0.1240 / 0.1440 / 0.17540 / 0.205402
Art. 8511
coating TiAlN nanoA
yes60 / 0.0660 / 0.10560 / 0.1360 / 0.15560 / 0.17560 / 0.2260 / 0.26414
Art. 8611
coating TiAlN nanoA
yes60 / 0.0660 / 0.10560 / 0.1360 / 0.15560 / 0.17560 / 0.2260 / 0.26414

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 414, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the M01 Austenitic (304, 316L) sub-group; they are not tuned to AISI 303. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling AISI 303: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.1.1Plunging801xD1xD0.010.020.0250.030.0350.050.060.06
M2.1.1Slotting801xD1xD0.0150.020.030.040.050.0650.080.08
M2.1.1Roughing1201.5xD0.33xD0.020.030.040.050.060.0850.1050.105
M2.1.1Finishing1602xD0.02xD0.020.0250.0350.0450.0550.070.090.09

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.1.1HPC Roughing5 Speed1253xD0.1xD0.0350.0550.070.090.1050.140.1750.175
M2.1.1HSC Roughing5 Speed1303xD0.08xD0.040.060.0750.0950.1150.1550.190.19
M2.1.1Finishing5 Speed1303xD0.02xD0.0150.020.030.0350.0450.060.070.07

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 65 HF (high-feed; catalogue page 705)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16
M2.1.1Slotting150see ap table1xD0.0260.0530.0790.1050.160.210.30.360.48
M2.1.1Roughing135see ap table0.4xD0.0370.0750.1120.150.2250.30.3750.450.6
M2.1.1(Pre-)Finishing135see ap table0.3xD0.030.060.090.120.180.240.30.360.48

ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:

MaterialHardnessØ 1Ø 2Ø 3Ø 4Ø 6Ø 8Ø 10Ø 12Ø 16
Pless than 850 N/mm²0.060.120.180.240.360.480.60.720.96
Pmore than 850 N/mm²0.050.10.150.20.30.40.50.60.8
Mless than 850 N/mm²0.040.080.120.160.240.320.40.480.64
Mmore than 850 N/mm²0.030.070.10.120.180.240.30.360.48
Kless than 240 HB0.060.120.180.240.360.480.60.720.96
Kmore than 240 HB0.050.10.150.20.30.40.50.60.8
STi alloys0.030.070.10.120.180.240.30.360.48
Hless than 55 HRC0.040.080.120.160.240.320.40.480.64
H55-65 HRC0.030.070.10.120.180.240.30.360.48

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M2.1.1Roughing1500.06xD0.2xD0.010.0190.0380.0580.0750.1150.1550.190.23
M2.1.1(Pre-)Finishing1350.02xD0.05xD0.010.0190.0380.0580.0750.1150.1550.190.23
M2.1.1Fine finishing1350.01xD0.02xD0.0080.0170.0340.050.0650.10.1350.170.2

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M2.1.1Roughing1150.04xD0.25xD0.0080.0160.0320.0490.0650.0950.130.160.195
M2.1.1(Pre-)Finishing950.03xD0.2xD0.0050.0110.0220.0320.0450.0650.0850.110.13
M2.1.1Fine finishing1050.01xD0.1xD0.0090.0170.0350.0520.070.1050.140.1750.205

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.1.1Roughing1550.1xD0.1xD0.0040.0080.0250.050.0650.0850.10.130.165
M2.1.1(Pre-)Finishing1200.02xD0.02xD0.0030.0050.0150.030.040.050.060.080.1
M2.1.1Fine finishing1200.01xD0.01xD0.0010.0030.0090.0150.0250.030.0350.0450.06

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the M01 Austenitic (304, 316L) sub-group; they are not tuned to AISI 303.

02e · REAMING

Reaming AISI 303: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.1.1: Stainless steel, austenitic, quenched, 180 HB800.10.20.250.450.60.70.750.80.850.95

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
M2.1.1: Stainless steel, austenitic, quenched, 180 HB800.80.850.90.95111.11.151.251.3

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
M2.1.1: Stainless steel, austenitic, quenched, 180 HB2011.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
M2.1.1: Stainless steel, austenitic, quenched, 180 HB201.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.1.1: Stainless steel, austenitic, quenched, 180 HB60.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.1.1: Stainless steel, austenitic, quenched, 180 HB100.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
M2.1.1: Stainless steel, austenitic, quenched, 180 HB60.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
M2.1.1: Stainless steel, austenitic, quenched, 180 HB60.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
M2.1.1: Stainless steel, austenitic, quenched, 180 HB60.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the M01 Austenitic (304, 316L) sub-group; they are not tuned to AISI 303.

03 · CARBIDE GRADES

Carbide grade class for AISI 303

Tough PVD-coated carbide. Roughing ≈ M25–M30 for heat and edge security; finishing ≈ M10–M20 for a sharper edge and better surface.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO M grade list and in the grade chart.

04 · DESIGNATIONS

AISI 303 in EN, US and JIS terms

EN X8CrNiS18-9, Werkstoffnummer 1.4305, US AISI 303 (UNS S30300), JIS SUS303. The full table, with the nearest-match flags, is on the AISI 303 / 1.4305 cross-reference page.

05 · NOTES

How X8CrNiS18-9 behaves in the cut

The free-machining austenitic: sulphur breaks the chips 304 will not. Runs faster and cleaner than 304 at the cost of corrosion resistance and weldability on the part.

Cost check · free · brand-neutral

Are you overpaying on your AISI 303 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for AISI 303?

The published starting band for the M01 Austenitic (304, 316L) sub-group is 120–200 m/min (395–655 sfm) at 0.10–0.35 mm/rev (.004–.014 ipr). It is a starting band for the whole sub-group, not a value tuned to AISI 303, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for AISI 303?

Tough PVD-coated carbide. Roughing ≈ M25–M30 for heat and edge security; finishing ≈ M10–M20 for a sharper edge and better surface. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is AISI 303 called in EN, US and JIS standards?

EN X8CrNiS18-9 (Werkstoffnummer 1.4305); US: AISI 303 (UNS S30300); JIS: SUS303. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.