CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · M MARTENSITIC STAINLESS (NI)

AISI 431 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for AISI 431 (X17CrNi16-2). The numbers are the published M20 Ferritic stainless sub-group starting band; the designations are on the cross-reference page.

ISO M · Stainless steel M20 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

AISI 431: group, sub-group and condition

ItemValue
ISO 513 groupM Stainless steel
Sub-groupM20 Ferritic stainless
Sub-group hardness / condition160–220 HB
CategoryMartensitic stainless (Ni)
EN / WerkstoffnummerX17CrNi16-2 · 1.4057

Hardness is the range published for the whole M20 Ferritic stainless sub-group on our material guide; the delivery condition of your AISI 431 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for AISI 431

ConditionVc m/minVc sfmFeed mm/revFeed ipr
M20 Ferritic stainless, 160–220 HB120–200395–6550.10–0.30.004–.012

Sub-group starting values for carbide inserts, from M20 Ferritic stainless. They describe the whole sub-group and are not tuned to AISI 431. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO M group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingPositive, sharp, honed edge; polished chipbreakerPVD-coated M-class carbideCoolant on the edgeConsistent depth of cut; do not dwell
FinishingKeen positive edge that shears instead of rubbingPVD-coated M-class carbide, sharp edgeCoolant on the edgeBuilt-up edge or smeared finish: raise Vc, sharper edge
Interrupted cutPositive honed edge, tougher edgePVD-coated M-class carbideCoolant on the edgeNotch wear at the DOC line: vary the depth of cut
Low rigidity / thin wallSharp positive edge; polished chipbreakerPVD-coated M-class carbideCoolant on the edgePoor finish from rubbing: keep the edge sharp

Setup rows are the selection table of the M20 Ferritic stainless guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: AISI 410 · X20Cr13 · AISI 430 · AISI 416 · AISI 440C

02b · DRILLING

Drilling AISI 431 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB (41 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no20 / 0.054------398
Art. 2469
coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295406
Art. 2471
Solid carbide drills, coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no35 / 0.03535 / 0.0635 / 0.07535 / 0.08535 / 0.135 / 0.12535 / 0.145403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no35 / 0.03535 / 0.0635 / 0.07535 / 0.08535 / 0.135 / 0.12535 / 0.145403
Art. 2474
Solid carbide drills, coating FIRE
no40 / 0.03540 / 0.0640 / 0.07540 / 0.08540 / 0.140 / 0.12540 / 0.145404
Art. 2477
coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295406
Art. 2479
Solid carbide drills, coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no35 / 0.03535 / 0.0635 / 0.07535 / 0.08535 / 0.135 / 0.12535 / 0.145403
Art. 2719
Solid carbide drills, coating FIRE
no40 / 0.03540 / 0.0640 / 0.07540 / 0.08540 / 0.140 / 0.12540 / 0.145404
Art. 2996
Solid carbide drills, coating FIRE
no40 / 0.03540 / 0.0640 / 0.07540 / 0.08540 / 0.140 / 0.12540 / 0.145404
Art. 4044
coating FIRE
yes55 / 0.05555 / 0.09555 / 0.11555 / 0.1455 / 0.1655 / 0.19555 / 0.235408
Art. 4045
coating FIRE
yes55 / 0.05555 / 0.09555 / 0.11555 / 0.1455 / 0.1655 / 0.19555 / 0.235408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.270 / 0.24570 / 0.295412
Art. 5499
Solid carbide drills, coating FIRE
yes65 / 0.0765 / 0.11565 / 0.14565 / 0.17565 / 0.265 / 0.24565 / 0.295413
Art. 5525
coating FIRE
yes55 / 0.05555 / 0.09555 / 0.11555 / 0.1455 / 0.1655 / 0.19555 / 0.235409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295407
Art. 5651
Solid carbide drills, coating FIRE
no40 / 0.03540 / 0.0640 / 0.07540 / 0.08540 / 0.140 / 0.12540 / 0.145404
Art. 6023
coating FIRE
yes55 / 0.0755 / 0.11555 / 0.14555 / 0.17555 / 0.255 / 0.24555 / 0.295406
Art. 6025
coating TiAlN nanoA
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.270 / 0.24570 / 0.295414
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no35 / 0.03535 / 0.0635 / 0.07535 / 0.08535 / 0.135 / 0.12535 / 0.145403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes65 / 0.059------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no25 / 0.059------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes65 / 0.059------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes65 / 0.059------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no35 / 0.068------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.1------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.1------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.1------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.1------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes70 / 0.054------397
Art. 6498
coating FIRE
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.270 / 0.24570 / 0.295412
Art. 6499
coating FIRE
yes65 / 0.0765 / 0.11565 / 0.14565 / 0.17565 / 0.265 / 0.24565 / 0.295413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.0790 / 0.11590 / 0.14590 / 0.17590 / 0.290 / 0.245-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.0790 / 0.11590 / 0.14590 / 0.17590 / 0.290 / 0.245-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.0790 / 0.11590 / 0.14590 / 0.17590 / 0.290 / 0.245-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.2--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.175---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes40 / 0.04540 / 0.07540 / 0.0940 / 0.1140 / 0.12540 / 0.15540 / 0.185402
Art. 8511
coating TiAlN nanoA
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.270 / 0.24570 / 0.295414
Art. 8611
coating TiAlN nanoA
yes70 / 0.0770 / 0.11570 / 0.14570 / 0.17570 / 0.270 / 0.24570 / 0.295414

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 414, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the M20 Ferritic stainless sub-group; they are not tuned to AISI 431. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling AISI 431: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M1.1.2Plunging1151xD1xD0.0150.020.0250.0350.040.0550.070.07
M1.1.2Slotting1151xD1xD0.0150.0250.030.0450.0550.070.090.09
M1.1.2Roughing1701.5xD0.33xD0.0250.0350.0450.060.070.0950.1150.115
M1.1.2Finishing2302xD0.02xD0.020.030.040.050.060.080.10.1

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M1.1.2HPC RoughingSpeed M1853xD0.1xD0.040.060.080.10.120.1550.1950.195
M1.1.2HSC RoughingSpeed M1953xD0.08xD0.0450.0650.0850.1050.130.170.2150.215
M1.1.2FinishingSpeed M1903xD0.02xD0.0150.0250.030.040.050.0650.080.08

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M1.1.2Roughing2000.1xD0.3xD0.0090.0180.0350.0530.070.1050.140.1750.21
M1.1.2(Pre-)Finishing1950.05xD0.1xD0.0110.0220.0430.0650.0850.130.1750.2150.26
M1.1.2Fine finishing2000.01xD0.02xD0.0090.0190.0380.0570.0750.1150.150.190.225

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M1.1.2Roughing1400.05xD0.4xD0.0070.0150.0290.0440.060.090.1150.1450.175
M1.1.2(Pre-)Finishing1450.03xD0.25xD0.0060.0120.0230.0350.0450.070.0950.1150.14
M1.1.2Fine finishing1500.01xD0.15xD0.0060.0130.0260.0390.050.0750.1050.130.155

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M1.1.2Roughing2300.1xD0.1xD0.0040.0090.0260.050.070.0850.1050.140.175
M1.1.2(Pre-)Finishing1800.03xD0.03xD0.0030.0050.0160.030.0450.0550.0650.0850.105
M1.1.2Fine finishing1800.01xD0.01xD0.0020.0030.0090.020.0250.030.0350.050.06

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the M20 Ferritic stainless sub-group; they are not tuned to AISI 431.

02e · REAMING

Reaming AISI 431: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB620.10.20.250.450.60.70.750.80.850.95

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB620.80.850.90.95111.11.151.251.3

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB3111.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB311.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB60.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB90.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB60.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB60.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
M1.1.2: Stainless steel, ferritic/martensitic, annealed, Rm 680 N/mm², 200 HB60.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the M20 Ferritic stainless sub-group; they are not tuned to AISI 431.

03 · CARBIDE GRADES

Carbide grade class for AISI 431

PVD-coated M-class carbide with a sharp positive edge.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO M grade list and in the grade chart.

04 · DESIGNATIONS

AISI 431 in EN, US and JIS terms

EN X17CrNi16-2, Werkstoffnummer 1.4057, US AISI 431 (UNS S43100), JIS SUS431. The full table, with the nearest-match flags, is on the AISI 431 / 1.4057 cross-reference page.

05 · NOTES

How X17CrNi16-2 behaves in the cut

Tough shaft-grade martensitic, usually cut quenched and tempered: stringy chips and higher cutting forces than 410. Chip control geometry matters more than raw speed.

Cost check · free · brand-neutral

Are you overpaying on your AISI 431 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for AISI 431?

The published starting band for the M20 Ferritic stainless sub-group is 120–200 m/min (395–655 sfm) at 0.10–0.30 mm/rev (.004–.012 ipr). It is a starting band for the whole sub-group, not a value tuned to AISI 431, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for AISI 431?

PVD-coated M-class carbide with a sharp positive edge. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is AISI 431 called in EN, US and JIS standards?

EN X17CrNi16-2 (Werkstoffnummer 1.4057); US: AISI 431 (UNS S43100); JIS: SUS431. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.