CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · P MEDIUM/HIGH-CARBON STEEL

AISI 1050 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for AISI 1050 (C50). The numbers are the published P02 Medium carbon steel sub-group starting band; the designations are on the cross-reference page.

ISO P · Steel P02 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

AISI 1050: group, sub-group and condition

ItemValue
ISO 513 groupP Steel
Sub-groupP02 Medium carbon steel
Sub-group hardness / condition160–220 HB
CategoryMedium/high-carbon steel
EN / WerkstoffnummerC50 · 1.0540

Hardness is the range published for the whole P02 Medium carbon steel sub-group on our material guide; the delivery condition of your AISI 1050 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for AISI 1050

ConditionVc m/minVc sfmFeed mm/revFeed ipr
P02 Medium carbon steel, 160–220 HB180–280590–9200.10–0.40.004–.016

Sub-group starting values for carbide inserts, from P02 Medium carbon steel. They describe the whole sub-group and are not tuned to AISI 1050. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO P group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingNegative for roughing and economy, medium chipbreakerCVD-coated carbidePer processChip control: match the chipbreaker to depth and feed
FinishingPositive for finishing, medium chipbreakerCVD-coated carbidePer processFlank wear sets tool life: balance Vc and grade
Interrupted cutNegative with a robust chipbreakerCVD-coated carbidePer processCrater wear at high speed: ease Vc
Low rigidity / thin wallPositive for low-rigidity workCVD-coated carbidePer processBuilt-up edge at low speed: raise Vc, sharper edge

Setup rows are the selection table of the P02 Medium carbon steel guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: AISI 1045 · AISI 1060 · AISI 1035

02b · DRILLING

Drilling AISI 1050 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB (44 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no45 / 0.095------398
Art. 2469
coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585406
Art. 2471
Solid carbide drills, coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585403
Art. 2474
Solid carbide drills, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585404
Art. 2477
coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585406
Art. 2479
Solid carbide drills, coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585403
Art. 2719
Solid carbide drills, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585404
Art. 2996
Solid carbide drills, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585404
Art. 4044
coating FIRE
yes130 / 0.11130 / 0.185130 / 0.235130 / 0.275130 / 0.315130 / 0.395130 / 0.47408
Art. 4045
coating FIRE
yes130 / 0.11130 / 0.185130 / 0.235130 / 0.275130 / 0.315130 / 0.395130 / 0.47408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes160 / 0.175160 / 0.295160 / 0.365160 / 0.43160 / 0.495160 / 0.615160 / 0.73412
Art. 5499
Solid carbide drills, coating FIRE
yes145 / 0.175145 / 0.295145 / 0.365145 / 0.43145 / 0.495145 / 0.615145 / 0.73413
Art. 5525
coating FIRE
yes100 / 0.11100 / 0.185100 / 0.235100 / 0.275100 / 0.315100 / 0.395100 / 0.47409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585407
Art. 5651
Solid carbide drills, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585404
Art. 6023
coating FIRE
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes100 / 0.216------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no90 / 0.216------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes95 / 0.108------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes95 / 0.108------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no80 / 0.216------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.135------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.135------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.081------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.081------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes90 / 0.121------397
Art. 6498
coating FIRE
yes160 / 0.175160 / 0.295160 / 0.365160 / 0.43160 / 0.495160 / 0.615160 / 0.73412
Art. 6499
coating FIRE
yes145 / 0.175145 / 0.295145 / 0.365145 / 0.43145 / 0.495145 / 0.615145 / 0.73413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.14110 / 0.235110 / 0.29110 / 0.345110 / 0.395110 / 0.495-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.14110 / 0.235110 / 0.29110 / 0.345110 / 0.395110 / 0.495-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.14110 / 0.235110 / 0.29110 / 0.345110 / 0.395110 / 0.495-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.1490 / 0.23590 / 0.2990 / 0.34590 / 0.395--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.1490 / 0.23590 / 0.2990 / 0.345---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes90 / 0.0790 / 0.11590 / 0.14590 / 0.17590 / 0.290 / 0.24590 / 0.295402
Art. 8520
coating Signum
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585410
Art. 8521
coating Signum
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585410
Art. 8522
coating Signum
yes130 / 0.085130 / 0.145130 / 0.18130 / 0.215130 / 0.25130 / 0.31130 / 0.365411
Art. 8524
coating Signum
no115 / 0.14115 / 0.235115 / 0.29115 / 0.345115 / 0.395115 / 0.495115 / 0.585405
Art. 8620
coating Signum
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585410
Art. 8621
coating Signum
yes130 / 0.14130 / 0.235130 / 0.29130 / 0.345130 / 0.395130 / 0.495130 / 0.585410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the P02 Medium carbon steel sub-group; they are not tuned to AISI 1050. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling AISI 1050: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.3Plunging2701xD1xD0.0150.0250.030.040.0450.060.0750.075
P1.1.3Slotting2701xD1xD0.020.0250.0350.050.060.080.10.1
P1.1.3Roughing3501.5xD0.4xD0.0250.040.050.0650.0750.10.1250.125
P1.1.3Finishing5402xD0.02xD0.020.0350.0450.0550.0650.090.110.11

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.3HPC RoughingSpeed M2603xD0.15xD0.040.060.080.0950.1150.1550.1950.195
P1.1.3HSC RoughingSpeed M2753xD0.1xD0.0450.070.0950.120.140.190.2350.235
P1.1.3HSC FinishingSpeed M2903xD0.01xD0.020.030.040.050.060.0750.0950.095

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P1.1.3Roughing3150.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
P1.1.3(Pre-)Finishing3050.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
P1.1.3Fine finishing3150.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P1.1.3Roughing2200.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
P1.1.3(Pre-)Finishing2250.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
P1.1.3Fine finishing2350.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.3Roughing3350.1xD0.1xD0.0050.010.0290.060.0750.0950.1150.1550.195
P1.1.3(Pre-)Finishing2650.03xD0.03xD0.0030.0060.0180.0350.0450.060.070.0950.12
P1.1.3Fine finishing2650.01xD0.01xD0.0020.0030.010.020.0250.0350.040.0550.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the P02 Medium carbon steel sub-group; they are not tuned to AISI 1050.

02d · TAPPING

Tapping AISI 1050 with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HBthrough-holes, VHM, coating TiCN46Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944)966

Values are for the catalogue material group(s) shown, which cover the P02 Medium carbon steel sub-group; they are not tuned to AISI 1050.

02e · REAMING

Reaming AISI 1050: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB1800.30.50.651.21.551.92.052.152.32.5

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB1802.152.32.42.52.62.72.93.053.253.4

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB3011.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB301.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB180.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB220.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB180.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB200.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
P1.1.3: Unalloyed steel, annealed, 0.45 % C, Rm 640 N/mm², 190 HB140.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the P02 Medium carbon steel sub-group; they are not tuned to AISI 1050.

03 · CARBIDE GRADES

Carbide grade class for AISI 1050

CVD-coated carbide, P15–P25; tougher for roughing, harder for finishing.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO P grade list and in the grade chart.

04 · DESIGNATIONS

AISI 1050 in EN, US and JIS terms

EN C50, Werkstoffnummer 1.0540, US AISI 1050 (UNS G10500), JIS S50C. The full table, with the nearest-match flags, is on the C50 / AISI 1050 cross-reference page.

05 · NOTES

How C50 behaves in the cut

Close to C45 with a touch more strength and flank-wear pressure. Mid-P data works; heat-treated condition moves it toward the tougher end.

Cost check · free · brand-neutral

Are you overpaying on your AISI 1050 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for AISI 1050?

The published starting band for the P02 Medium carbon steel sub-group is 180–280 m/min (590–920 sfm) at 0.10–0.40 mm/rev (.004–.016 ipr). It is a starting band for the whole sub-group, not a value tuned to AISI 1050, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for AISI 1050?

CVD-coated carbide, P15–P25; tougher for roughing, harder for finishing. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is AISI 1050 called in EN, US and JIS standards?

EN C50 (Werkstoffnummer 1.0540); US: AISI 1050 (UNS G10500); JIS: S50C. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.