CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · N ALUMINIUM (HIGH STRENGTH)

EN AW-7075 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for EN AW-7075 (AlZn5.5MgCu). The numbers are the published N01 Aluminium (wrought) sub-group starting band; the designations are on the cross-reference page.

ISO N · Non-ferrous N01 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

EN AW-7075: group, sub-group and condition

ItemValue
ISO 513 groupN Non-ferrous
Sub-groupN01 Aluminium (wrought)
Sub-group hardness / condition~65 HB
CategoryAluminium (high strength)
EN / WerkstoffnummerEN AW-7075 (AlZn5,5MgCu) · 3.4365

Hardness is the range published for the whole N01 Aluminium (wrought) sub-group on our material guide; the delivery condition of your EN AW-7075 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for EN AW-7075

ConditionVc m/minVc sfmFeed mm/revFeed ipr
N01 Aluminium (wrought), ~65 HB300–1000985–32800.05–0.30.002–.012

Sub-group starting values for carbide inserts, from N01 Aluminium (wrought). They describe the whole sub-group and are not tuned to EN AW-7075. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO N group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingSharp, high positive rake, polished flute, open chipbreakerUncoated or DLC-coated fine-grain carbide; PCD for long runsCoolant or MQL to flush chipsChip evacuation: open chipbreaker, polished flutes
FinishingSharp, high positive rake, polished fluteUncoated or DLC-coated carbide; PCD for abrasive alloysCoolant or MQLBuilt-up edge: raise feed per tooth, do not only raise speed
Interrupted cutSharp positive edge, open chipbreakerUncoated or DLC-coated carbideCoolant or MQLChip load too low makes the edge rub instead of shear
Low rigidity / thin wallKeen edge to shear rather than rubUncoated or DLC-coated carbideCoolant or MQLFeed per tooth against radial chip thinning

Setup rows are the selection table of the N01 Aluminium (wrought) guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: EN AW-2024 · EN AW-5083 · EN AW-6061 · EN AW-6082 · EN AW-5754 · EN AW-2007

02b · DRILLING

Drilling EN AW-7075 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB (36 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no160 / 0.18------398
Art. 768yes210 / 0.155210 / 0.26210 / 0.325210 / 0.385210 / 0.44210 / 0.55210 / 0.65418
Art. 773yes210 / 0.125210 / 0.21210 / 0.26210 / 0.305210 / 0.355210 / 0.44210 / 0.52424
Art. 2469
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 2471
Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2474
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 2477
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 2479
Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2719
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 2996
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 4044
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65408
Art. 4045
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65408
Art. 5525
coating FIRE
yes185 / 0.125185 / 0.21185 / 0.26185 / 0.305185 / 0.355185 / 0.44185 / 0.52409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 5651
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 5768
Solid carbide drills with coolant ducts
yes240 / 0.19240 / 0.325240 / 0.405240 / 0.48240 / 0.55240 / 0.685240 / 0.815415
Art. 6023
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 6068yes200 / 0.155200 / 0.26200 / 0.325200 / 0.385200 / 0.44200 / 0.55200 / 0.65421
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes150 / 0.33------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no100 / 0.33------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.27------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.27------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no270 / 0.18------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.18------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.18------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.12------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.12------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes135 / 0.18------397
Art. 6515yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6516
Ratio drills with coolant ducts
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6517
Ratio drills with coolant ducts
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes185 / 0.095185 / 0.165185 / 0.205185 / 0.24185 / 0.275185 / 0.345185 / 0.405402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 415, 418, 421, 424, 425).

N1.1.2: Wrought aluminium alloys, hardened, 100 HB (36 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no160 / 0.18------398
Art. 768yes210 / 0.155210 / 0.26210 / 0.325210 / 0.385210 / 0.44210 / 0.55210 / 0.65418
Art. 773yes210 / 0.125210 / 0.21210 / 0.26210 / 0.305210 / 0.355210 / 0.44210 / 0.52424
Art. 2469
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 2471
Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2474
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 2477
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 2479
Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 2719
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 2996
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 4044
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65408
Art. 4045
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65408
Art. 5525
coating FIRE
yes185 / 0.125185 / 0.21185 / 0.26185 / 0.305185 / 0.355185 / 0.44185 / 0.52409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65407
Art. 5651
Solid carbide drills, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52404
Art. 5768
Solid carbide drills with coolant ducts
yes240 / 0.19240 / 0.325240 / 0.405240 / 0.48240 / 0.55240 / 0.685240 / 0.815415
Art. 6023
coating FIRE
yes185 / 0.155185 / 0.26185 / 0.325185 / 0.385185 / 0.44185 / 0.55185 / 0.65406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no165 / 0.125165 / 0.21165 / 0.26165 / 0.305165 / 0.355165 / 0.44165 / 0.52403
Art. 6068yes200 / 0.155200 / 0.26200 / 0.325200 / 0.385200 / 0.44200 / 0.55200 / 0.65421
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes150 / 0.33------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no100 / 0.33------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.27------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.27------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no270 / 0.18------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.18------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.18------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.12------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes300 / 0.12------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes135 / 0.18------397
Art. 6515yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6516
Ratio drills with coolant ducts
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6517
Ratio drills with coolant ducts
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44--425
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes185 / 0.095185 / 0.165185 / 0.205185 / 0.24185 / 0.275185 / 0.345185 / 0.405402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 415, 418, 421, 424, 425).

Values are for the catalogue material group(s) shown, which cover the N01 Aluminium (wrought) sub-group; they are not tuned to EN AW-7075. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling EN AW-7075: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N1.1.1, N1.1.2Plunging5001xD1xD0.020.030.040.050.060.080.10.1
N1.1.1, N1.1.2Slotting5001xD1xD0.0250.0350.0450.0650.080.1050.130.13
N1.1.1, N1.1.2Roughing6501.5xD0.4xD0.0350.050.0650.080.10.130.1650.165
N1.1.1, N1.1.2Finishing10002xD0.02xD0.030.0450.0550.070.0850.1150.1450.145

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N1.1.1, N1.1.2HPC Roughing5 Speed6903xD0.2xD0.0450.0650.090.110.130.1750.220.22
N1.1.1, N1.1.2HSC Roughing5 Speed7303xD0.15xD0.050.080.1050.130.1550.210.260.26
N1.1.1, N1.1.2Finishing5 Speed8003xD0.02xD0.030.040.0550.070.0850.1150.140.14

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

RF 100 A for unstable conditions (roughing end mill; catalogue page 703)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20fz Ø 25
N1.1.1, N1.1.2Slotting3751xD1xD0.010.0150.020.0250.0350.0450.060.0750.095
N1.1.1, N1.1.2Roughing4301xD0.75xD0.0130.0150.0250.0350.0450.050.070.0850.105

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio roughing end mills Alu RF 100 A: Art. 6866, 6868, 6869, 6870, 6871, 6974, 6975, 6976, 6977. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

Diamond-coated milling cutters for fibre-reinforced plastics and graphite (slot drill, end mill, corner radius / torus, ball nose; catalogue page 704)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N1.1.1, N1.1.2Slotting4501xD1xD0.0210.030.0450.0550.080.10.130.165
N1.1.1, N1.1.2Roughing5201xD0.75xD0.0280.0350.0550.0750.0950.110.150.185
N1.1.1, N1.1.2Finishing9001xD0.02xD0.0270.0350.0550.070.090.1050.1450.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: PCD slot drills (2-fluted): Art. 5492, 5493; PCD slot drills (3-fluted): Art. 5495, 5496; Kevlar end mills CR 100: Art. 6717, 6719, 6720; Slot drills XL (3-fluted): Art. 6721; Slot drills with corner radius (2-fluted): Art. 6722; End mills with corner radius (4-fluted): Art. 6723; Ball nose slot drills (2-fluted): Art. 6724; Ball nose end mills (4-fluted): Art. 6725; Kevlar end mills FR 100: Art. 6769, 6770, 6805, 6806. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
N1.1.1, N1.1.2Roughing8950.1xD0.3xD0.0110.0210.0430.0640.0850.130.170.2150.255
N1.1.1, N1.1.2(Pre-)Finishing8650.05xD0.1xD0.0130.0260.0530.0790.1050.160.210.2650.315
N1.1.1, N1.1.2Fine finishing8950.01xD0.02xD0.0120.0230.0460.0690.090.140.1850.230.275

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
N1.1.1, N1.1.2Roughing6200.05xD0.4xD0.0090.0180.0360.0540.070.110.1450.180.215
N1.1.1, N1.1.2(Pre-)Finishing6450.03xD0.25xD0.0070.0140.0290.0430.060.0850.1150.1450.175
N1.1.1, N1.1.2Fine finishing6700.01xD0.15xD0.0080.0160.0320.0480.0650.0950.1250.160.19

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N1.1.1, N1.1.2Roughing5700.1xD0.1xD0.0070.0150.0450.090.120.150.180.240.3
N1.1.1, N1.1.2(Pre-)Finishing4500.03xD0.03xD0.0050.0090.0270.0550.0750.090.110.1450.18
N1.1.1, N1.1.2Fine finishing4500.01xD0.01xD0.0030.0050.0160.030.040.050.060.0850.105

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the N01 Aluminium (wrought) sub-group; they are not tuned to EN AW-7075.

02e · REAMING

Reaming EN AW-7075: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 Alu (solid carbide; catalogue page 1043)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB2200.550.751.351.752.152.32.452.62.85
N1.1.2: Wrought aluminium alloys, hardened, 100 HB2200.550.751.351.752.152.32.452.62.85

f in mm/rev. Reamers this table belongs to: Art. 1678, Art. 1679.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB300.030.050.10.150.30.350.450.450.50.550.6
N1.1.2: Wrought aluminium alloys, hardened, 100 HB300.030.050.10.150.30.350.450.450.50.550.6

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB340.030.050.10.150.30.350.450.450.50.550.6
N1.1.2: Wrought aluminium alloys, hardened, 100 HB340.030.050.10.150.30.350.450.450.50.550.6

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB300.030.050.10.150.250.30.40.450.50.50.60.65
N1.1.2: Wrought aluminium alloys, hardened, 100 HB300.030.050.10.150.250.30.40.450.50.50.60.65

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB300.10.150.250.30.40.40.450.45
N1.1.2: Wrought aluminium alloys, hardened, 100 HB300.10.150.250.30.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
N1.1.1: Wrought aluminium alloys, non-hardened, 60 HB250.250.30.30.350.350.40.450.45
N1.1.2: Wrought aluminium alloys, hardened, 100 HB250.250.30.30.350.350.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the N01 Aluminium (wrought) sub-group; they are not tuned to EN AW-7075.

03 · CARBIDE GRADES

Carbide grade class for EN AW-7075

Uncoated or DLC-coated fine-grain carbide with high positive rake and polished flutes; PCD for long production runs or abrasive high-silicon alloys.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO N grade list and in the grade chart.

04 · DESIGNATIONS

EN AW-7075 in EN, US and JIS terms

EN AW-7075 (AlZn5,5MgCu), Werkstoffnummer 3.4365, US UNS A97075, JIS A7075. The full table, with the nearest-match flags, is on the EN AW-7075 / AlZn5.5MgCu cross-reference page.

05 · NOTES

How EN AW-7075 behaves in the cut

The strongest common aluminium: stiff, slightly abrasive, superb chips in T6/T651. Watch residual-stress distortion on thin walls; the machining itself is the easy part.

Cost check · free · brand-neutral

Are you overpaying on your EN AW-7075 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for EN AW-7075?

The published starting band for the N01 Aluminium (wrought) sub-group is 300–1000 m/min (985–3280 sfm) at 0.05–0.30 mm/rev (.002–.012 ipr). It is a starting band for the whole sub-group, not a value tuned to EN AW-7075, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for EN AW-7075?

Uncoated or DLC-coated fine-grain carbide with high positive rake and polished flutes; PCD for long production runs or abrasive high-silicon alloys. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is EN AW-7075 called in EN, US and JIS standards?

EN AW-7075 (AlZn5,5MgCu) (Werkstoffnummer 3.4365); US: UNS A97075; JIS: A7075. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.