CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · P MOLD STEEL (PRE-HARDENED)

AISI P20 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for AISI P20 (40CrMnMo7). The numbers are the published P20 Alloy steel (heat treated) sub-group starting band; the designations are on the cross-reference page.

ISO P · Steel P20 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

AISI P20: group, sub-group and condition

ItemValue
ISO 513 groupP Steel
Sub-groupP20 Alloy steel (heat treated)
Sub-group hardness / condition200–300 HB
CategoryMold steel (pre-hardened)
EN / Werkstoffnummer40CrMnMo7 · 1.2311

Hardness is the range published for the whole P20 Alloy steel (heat treated) sub-group on our material guide; the delivery condition of your AISI P20 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for AISI P20

ConditionVc m/minVc sfmFeed mm/revFeed ipr
P20 Alloy steel (heat treated), 200–300 HB150–250490–8200.10–0.40.004–.016

Sub-group starting values for carbide inserts, from P20 Alloy steel (heat treated). They describe the whole sub-group and are not tuned to AISI P20. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO P group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingNegative geometry, economical for roughingCVD-coated carbide with a hard top layer for crater resistanceCheck coolant deliveryCrater wear on the rake face: ease Vc
FinishingPositive geometry for finishingCVD-coated carbideCheck coolant deliveryPlastic deformation: edge too hot, drop Vc and feed
Interrupted cutHoned or chamfered edge for securityCVD-coated carbideCheck coolant deliveryEdge security in interruptions; lower the band as hardness climbs
Low rigidity / thin wallPositive geometry for thin walls and low-rigidity setupsCVD-coated carbideCheck coolant deliveryBuilt-up edge at low speed: raise Vc

Setup rows are the selection table of the P20 Alloy steel (heat treated) guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: AISI H13 · AISI O1 · AISI O2 · AISI H11

02b · DRILLING

Drilling AISI P20 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB (45 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no30 / 0.087------398
Art. 1946
Solid carbide drills, coating TiAlN
no80 / 0.09580 / 0.16580 / 0.20580 / 0.2480 / 0.27580 / 0.34580 / 0.405434
Art. 2469
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 2471
Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2474
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 2477
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 2479
Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2719
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 2996
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 4044
coating FIRE
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405408
Art. 4045
coating FIRE
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55120 / 0.65412
Art. 5499
Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 5525
coating FIRE
yes110 / 0.095110 / 0.165110 / 0.205110 / 0.24110 / 0.275110 / 0.345110 / 0.405409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 5651
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 6023
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes90 / 0.21------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no80 / 0.21------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes90 / 0.12------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes90 / 0.12------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no80 / 0.21------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.15------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.15------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.09------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.09------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes90 / 0.105------397
Art. 6498
coating FIRE
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55120 / 0.65412
Art. 6499
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.125100 / 0.21100 / 0.26100 / 0.305100 / 0.355100 / 0.44-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.355--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.305---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes80 / 0.0680 / 0.10580 / 0.1380 / 0.15580 / 0.17580 / 0.2280 / 0.26402
Art. 8520
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8521
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8522
coating Signum
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405411
Art. 8524
coating Signum
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52405
Art. 8620
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8621
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430, 434).

Values are for the catalogue material group(s) shown, which cover the P20 Alloy steel (heat treated) sub-group; they are not tuned to AISI P20. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling AISI P20: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.2Plunging2301xD1xD0.0150.0250.030.040.0450.060.0750.075
P2.1.2Slotting2301xD1xD0.020.0250.0350.050.060.080.10.1
P2.1.2Roughing3001.5xD0.4xD0.0250.040.050.0650.0750.10.1250.125
P2.1.2Finishing4602xD0.02xD0.020.0350.0450.0550.0650.090.110.11

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.2HPC RoughingSpeed M2353xD0.15xD0.0350.0550.070.090.1050.1450.180.18
P2.1.2HSC RoughingSpeed M2453xD0.1xD0.0450.0650.0850.110.130.1750.2150.215
P2.1.2HSC FinishingSpeed M2553xD0.01xD0.020.0250.0350.0450.0550.070.090.09

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 65 HF (high-feed; catalogue page 705)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16
P2.1.2Slotting285see ap table1xD0.0310.0620.0920.1250.1850.2450.350.420.56
P2.1.2Roughing275see ap table0.6xD0.0420.0840.1260.170.250.3350.420.5050.67
P2.1.2(Pre-)Finishing285see ap table0.4xD0.0350.070.1050.140.210.280.350.420.56

ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:

MaterialHardnessØ 1Ø 2Ø 3Ø 4Ø 6Ø 8Ø 10Ø 12Ø 16
Pless than 850 N/mm²0.060.120.180.240.360.480.60.720.96
Pmore than 850 N/mm²0.050.10.150.20.30.40.50.60.8
Mless than 850 N/mm²0.040.080.120.160.240.320.40.480.64
Mmore than 850 N/mm²0.030.070.10.120.180.240.30.360.48
Kless than 240 HB0.060.120.180.240.360.480.60.720.96
Kmore than 240 HB0.050.10.150.20.30.40.50.60.8
STi alloys0.030.070.10.120.180.240.30.360.48
Hless than 55 HRC0.040.080.120.160.240.320.40.480.64
H55-65 HRC0.030.070.10.120.180.240.30.360.48

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P2.1.2Roughing2850.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
P2.1.2(Pre-)Finishing2750.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
P2.1.2Fine finishing2850.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P2.1.2Roughing1950.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
P2.1.2(Pre-)Finishing2050.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
P2.1.2Fine finishing2100.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.2Roughing3350.1xD0.1xD0.0050.010.0290.060.0750.0950.1150.1550.195
P2.1.2(Pre-)Finishing2650.03xD0.03xD0.0030.0060.0180.0350.0450.060.070.0950.12
P2.1.2Fine finishing2650.01xD0.01xD0.0020.0030.010.020.0250.0350.040.0550.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the P20 Alloy steel (heat treated) sub-group; they are not tuned to AISI P20.

02d · TAPPING

Tapping AISI P20 with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HBthrough-holes, VHM, coating TiCN33Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944)966

Values are for the catalogue material group(s) shown, which cover the P20 Alloy steel (heat treated) sub-group; they are not tuned to AISI P20.

02e · REAMING

Reaming AISI P20: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB1800.30.450.61.151.451.751.92.052.152.35

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB1802.052.152.252.352.452.552.72.853.053.2

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB3011.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB301.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB140.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB180.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB140.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB160.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
P2.1.2: Low-alloy steel, heat-treated, Rm 930 N/mm², 275 HB120.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the P20 Alloy steel (heat treated) sub-group; they are not tuned to AISI P20.

03 · CARBIDE GRADES

Carbide grade class for AISI P20

CVD-coated carbide for crater resistance. Heat-treated alloy steels like 42CrMo4 / 4140 (≈ 28–34 HRC) reward a hard CVD top layer: roughing around P25–P35, finishing around P10–P20.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO P grade list and in the grade chart.

04 · DESIGNATIONS

AISI P20 in EN, US and JIS terms

EN 40CrMnMo7, Werkstoffnummer 1.2311, US AISI P20 (UNS T51620). The full table, with the nearest-match flags, is on the P20 / 1.2311 cross-reference page.

05 · NOTES

How 40CrMnMo7 behaves in the cut

Delivered pre-hardened around 28-34 HRC and machined in that state: firmly P20-position work. 1.2738 is the nickel-alloyed P20 variant for thicker sections and cuts similarly.

Cost check · free · brand-neutral

Are you overpaying on your AISI P20 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for AISI P20?

The published starting band for the P20 Alloy steel (heat treated) sub-group is 150–250 m/min (490–820 sfm) at 0.10–0.40 mm/rev (.004–.016 ipr). It is a starting band for the whole sub-group, not a value tuned to AISI P20, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for AISI P20?

CVD-coated carbide for crater resistance. Heat-treated alloy steels like 42CrMo4 / 4140 (≈ 28–34 HRC) reward a hard CVD top layer: roughing around P25–P35, finishing around P10–P20. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is AISI P20 called in EN, US and JIS standards?

EN 40CrMnMo7 (Werkstoffnummer 1.2311); US: AISI P20 (UNS T51620); JIS: none listed. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.