CUTTINGTOOLS / AI
Find equivalents

ISO 513 application group · brand-neutral

ISO K grades — cast iron

Two different K scales, and they are not the same. On a workpiece chart, K plus a number describes the material you are cutting. On an insert box, K plus a number describes what the grade is built for. The letter is shared, so a K-group material is cut with K-group grades. The numbers are not: a workpiece subgroup number and a grade's application number come from different scales and must never be matched to each other. Everything on this page is the grade side.

ISO K is the cast iron group. 165 grades from 14 manufacturers are placed somewhere in it across 6 application classes, according to the comparison charts the makers publish themselves.

What the number after the K means

Inside a letter the two-digit number is a position on one axis: the low numbers are the wear-resistant, harder grades meant for finishing cuts at higher speed and lighter load, the high numbers are the tougher grades meant for roughing, interrupted cuts and less stable setups. It is a continuum, not a set of boxes, and makers place their own grades on it.

Grades at each K class

Two grades in the same class are built for the same job. They are not identical: substrate, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from.

K01

15 grades from 7 manufacturers are placed at K01. The 3 below have a cross-brand equivalence page: Mitsubishi MB5015 · Mitsubishi MB710 · Sumitomo BN500 and 12 more.

K05

24 grades from 12 manufacturers are placed at K05. The 7 below have a cross-brand equivalence page: ISCAR IC5005 · Mitsubishi MP8010 · NTK CP1 · Sumitomo AC4010K · TaeguTec TT7005 · Tungaloy T5105 · Walter WKK10S and 17 more.

K10

81 grades from 14 manufacturers are placed at K10. The 14 below have a cross-brand equivalence page: ISCAR IC5005 · ISCAR IC5010 · Kennametal KCK15B · Kyocera CA4515 · Mitsubishi MB5015 · Mitsubishi MB710 · Mitsubishi MC5115 · Mitsubishi MP8010 · NTK CP1 · Sumitomo AC4010K · Sumitomo BN500 · TaeguTec TT7005 · TaeguTec TT9030 · Tungaloy AH710 and 67 more.

K15

22 grades from 10 manufacturers are placed at K15. The 7 below have a cross-brand equivalence page: ISCAR IC5010 · Kennametal KCK15B · Kyocera CA4515 · Kyocera TN60 · MOLDINO CZ25 · Mitsubishi MC5115 · Tungaloy AT9530 and 15 more.

K20

73 grades from 13 manufacturers are placed at K20. The 10 below have a cross-brand equivalence page: Kennametal KC5025 · Kennametal KCU25 · MOLDINO GM8020 · Mitsubishi MBS140 · Seco MK2050 · Sumitomo AC530U · Sumitomo BNS8125 · Tungaloy BX90S · Tungaloy BXC90 · Walter WKP35S and 63 more.

K30

19 grades from 7 manufacturers are placed at K30. The 6 below have a cross-brand equivalence page: MOLDINO CY250 · Mitsubishi MBS140 · Seco MK2050 · Sumitomo BNS8125 · Tungaloy BX90S · Tungaloy BXC90 and 13 more.

Where these numbers come from

Every placement above is read from a grade comparison chart published by a manufacturer, cross-checked against other makers' charts. Nothing is inferred from price, availability or popularity, and no manufacturer pays to appear here. Something wrong on this page? research@cuttingtoolsai.eu.

Looking for the workpiece side instead — which steel, stainless or iron falls in which group? That is the ISO material groups chart.

Looking for one maker's grades instead? See the Kennametal insert grade chart or all brand grade charts.

Cost check · free · brand-neutral

Are you overpaying on your ISO K inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Want every brand in one printable PDF?
Free 8-brand grade comparison PDF. Same provenance rules as this page: nothing guessed, sources recorded.
Free 8-brand PDF

Get the chart pack →

Have your own tool list? Free coverage check. Sourced report from EUR 9 for one grade.

Ask about your own case

Material, operation, machine — get a grade and a starting cutting data set, grounded in the same reference data.