CUTTINGTOOLS / AI
Find equivalents

ISO 513 application group · brand-neutral

ISO S grades — superalloys & titanium

Two different S scales, and they are not the same. On a workpiece chart, S plus a number describes the material you are cutting. On an insert box, S plus a number describes what the grade is built for. The letter is shared, so a S-group material is cut with S-group grades. The numbers are not: a workpiece subgroup number and a grade's application number come from different scales and must never be matched to each other. Everything on this page is the grade side.

ISO S is the superalloys & titanium group. 74 grades from 13 manufacturers are placed somewhere in it across 7 application classes, according to the comparison charts the makers publish themselves.

What the number after the S means

Inside a letter the two-digit number is a position on one axis: the low numbers are the wear-resistant, harder grades meant for finishing cuts at higher speed and lighter load, the high numbers are the tougher grades meant for roughing, interrupted cuts and less stable setups. It is a continuum, not a set of boxes, and makers place their own grades on it.

Grades at each S class

Two grades in the same class are built for the same job. They are not identical: substrate, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from.

S01

3 grades from 3 manufacturers are placed at S01: ISCAR IB05S · Mitsubishi MB730 · Tungaloy BX950.

S05

11 grades from 9 manufacturers are placed at S05. The 4 below have a cross-brand equivalence page: ISCAR IC806 · Sandvik GC1105 · Tungaloy KS05F · Walter WSM01 and 7 more.

S10

30 grades from 12 manufacturers are placed at S10. The 8 below have a cross-brand equivalence page: ISCAR IC806 · Sandvik GC1105 · Sumitomo EH510 · TaeguTec TT3010 · TaeguTec TT5080 · Tungaloy KS05F · Walter WSM01 · Walter WSM10S and 22 more.

S15

15 grades from 8 manufacturers are placed at S15. The 2 below have a cross-brand equivalence page: TaeguTec TT3010 · Walter WSM10S and 13 more.

S20

28 grades from 12 manufacturers are placed at S20. The 7 below have a cross-brand equivalence page: Dijet JC5015 · Kennametal KC5025 · Kennametal KCU25 · Sandvik GC1125 · Sumitomo EH520 · Tungaloy AH630 · Walter WSM20S and 21 more.

S25

18 grades from 11 manufacturers are placed at S25. The 5 below have a cross-brand equivalence page: Dijet JC5015 · Kennametal KC5025 · Kennametal KCU25 · Sandvik GC1125 · Walter WSM20S and 13 more.

S30

3 grades from 3 manufacturers are placed at S30: Mitsubishi VP20RT · TaeguTec TT8020 · Walter WSM30S.

Where these numbers come from

Every placement above is read from a grade comparison chart published by a manufacturer, cross-checked against other makers' charts. Nothing is inferred from price, availability or popularity, and no manufacturer pays to appear here. Something wrong on this page? research@cuttingtoolsai.eu.

Looking for the workpiece side instead — which steel, stainless or iron falls in which group? That is the ISO material groups chart.

Looking for one maker's grades instead? See the Kennametal insert grade chart or all brand grade charts.

Cost check · free · brand-neutral

Are you overpaying on your ISO S inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Want every brand in one printable PDF?
Free 8-brand grade comparison PDF. Same provenance rules as this page: nothing guessed, sources recorded.
Free 8-brand PDF

Get the chart pack →

Have your own tool list? Free coverage check. Sourced report from EUR 9 for one grade.

Ask about your own case

Material, operation, machine — get a grade and a starting cutting data set, grounded in the same reference data.