Cross-brand grade equivalence · brand-neutral
Sandvik GC1125: candidate alternatives
How to read this page. These alternatives are compiled from grade comparison charts the manufacturers publish themselves. A direct peer is a grade listed in the same row of a manufacturer comparison chart as GC1125: that is chart comparability, not verified cutting performance and not a drop-in swap. Grades that share only the ISO 513 application position are listed apart, marked not verified. Substrate, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Validate any swap on a sample part before you change production. Something wrong on this page, or a grade you want removed? research@cuttingtoolsai.eu.
Sandvik GC1125 sits at ISO 513 application classes P20, P30, S20, S25 — steel, superalloys and titanium. 16 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 159 more grades share an ISO position only and are not verified.
Alternatives by evidence
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- Mitsubishi VP15TF ISO P20 P30 S20 S25 · 2 charts (Ingersoll, Tungaloy) · carbide
- Mitsubishi MP9025 ISO S20 S25 · 2 charts (Ingersoll, Tungaloy)
- Seco CP500 ISO S20 S25 · 2 charts (Ingersoll, Tungaloy)
- Tungaloy AH725 ISO P20 P30 S20 S25 · 2 charts (Ingersoll, Tungaloy)
- Walter WSM20S ISO S20 S25 · 2 charts (Ingersoll, Tungaloy)
- ISCAR IC908 ISO P20 S20 S25 · 1 chart (Ingersoll)
- TaeguTec TT9030 ISO P20 P30 · 1 chart (Ingersoll)
- TaeguTec TT9080 ISO S20 S25 · 1 chart (Ingersoll)
- Mitsubishi VP20RT ISO P20 P30 · 2 charts (Ingersoll, Tungaloy)
- Walter WSM30S ISO S20 · 2 charts (Ingersoll, Tungaloy)
- Korloy PC5300 ISO S20 · 1 chart (Ingersoll)
- Seco TS2500 ISO P20 · 2 charts (Ingersoll, Tungaloy)
- Ceratizit CTPM125 ISO P20 · 1 chart (Tungaloy)
- ISCAR IC808 ISO P05 P10 · 1 chart (Ingersoll)
- Tungaloy AH630 ISO S20 · 2 charts (Ingersoll, Tungaloy)
- Tungaloy AH645 ISO S20 · 2 charts (Ingersoll, Tungaloy)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Kyocera PR1535 ISO P30 S20 S25 · not verified · carbide
- Tungaloy AH120 ISO P20 P30 S25 · not verified
- Sumitomo T2500Z ISO P20 P30 · not verified · cermet
- Kennametal KC9125 ISO P20 · not verified
- Kyocera PV730 ISO P30 · not verified · cermet
111 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- ISCAR IC8350 ISO P30 · not verified
- Tungaloy UX30 ISO P30 · not verified
- ISCAR IC50M ISO P30 · not verified
- Kennametal KCP30B ISO P30 · not verified
- TaeguTec TT8020 ISO P30 · not verified
18 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kyocera PV720 ISO P20 · not verified · cermet
- Kyocera TN620 ISO P20 · not verified · cermet
- ISCAR IC907 ISO P20 · not verified
- Mitsubishi NX2525 ISO P20 · not verified · cermet
- NTK DM4 ISO P20 · not verified
15 more not shown.
The free check and the report show each grade with its sources: check GC1125 free.
What this does and does not tell you
An ISO 513 application class says which material group and which range of operations a grade is built for. Two grades sharing a class are built for the same job. They are not identical: substrate grain, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Treat a candidate here as the shortlist for your own trial, not as a drop-in replacement.
Everything above is derived from the makers' own published application data. Nothing is inferred from price, availability or popularity, and no manufacturer pays to appear here.
Related candidate alternatives
- Sandvik GC4305 P05, P10
- Sandvik GC1105 M10, S05, S10
- Sandvik GC4325 P20, P25, P30
- Sandvik GC1030 M10, P30
- Sumitomo AC530U K20, M30, M35, P20
- Sandvik GC1025 M10, P20
All cross-brand grade candidates
Check Sandvik GC1125 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Are you overpaying on your Sandvik GC1125 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Ask about your own case
Material, operation, machine — get a grade and a starting cutting data set, grounded in the same reference data.