Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for 11SMn30 (W.-Nr. 1.0715). The numbers are the published P40 Free-cutting steel sub-group starting band; the designations are on the cross-reference page.
| Item | Value |
|---|---|
| ISO 513 group | P Steel |
| Sub-group | P40 Free-cutting steel |
| Sub-group hardness / condition | 160–230 HB |
| Category | Free-cutting steel |
| EN / Werkstoffnummer | 11SMn30 · 1.0715 |
Hardness is the range published for the whole P40 Free-cutting steel sub-group on our material guide; the delivery condition of your 11SMn30 may sit anywhere inside it or outside it.
At least one designation of this material is a nearest commonly-cited counterpart, not a same-composition equivalent. The machining values below belong to the sub-group, so confirm the actual alloy and delivery condition on the material certificate.
| Condition | Vc m/min | Vc sfm | Feed mm/rev | Feed ipr |
|---|---|---|---|---|
| P40 Free-cutting steel, 160–230 HB | 200–350 | 655–1150 | 0.10–0.40 | .004–.016 |
Sub-group starting values for carbide inserts, from P40 Free-cutting steel. They describe the whole sub-group and are not tuned to 11SMn30. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO P group range.
| Operation | Geometry | Coating family | Coolant | First check |
|---|---|---|---|---|
| Roughing | Positive sharp edge; chip control is rarely a problem | Coated carbide | Per process | Speed in band: built-up edge is the one common issue |
| Finishing | Positive sharp edge | Coated carbide | Per process | Finish drop with a dull edge: replace a worn edge |
| Interrupted cut | Positive edge with a light hone | Coated carbide | Per process | Lead-free substitutes machine differently: re-tune speeds |
| Low rigidity / thin wall | Positive sharp edge | Coated carbide | Per process | Mostly low speed or a dull edge |
Setup rows are the selection table of the P40 Free-cutting steel guide. They carry no speeds, so they do not change the starting band above.
One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 50 / 0.105 | - | - | - | - | - | - | 398 |
| Art. 2469 coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 404 |
| Art. 2477 coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 404 |
| Art. 4044 coating FIRE | yes | 145 / 0.125 | 145 / 0.21 | 145 / 0.26 | 145 / 0.305 | 145 / 0.355 | 145 / 0.44 | 145 / 0.52 | 408 |
| Art. 4045 coating FIRE | yes | 145 / 0.125 | 145 / 0.21 | 145 / 0.26 | 145 / 0.305 | 145 / 0.355 | 145 / 0.44 | 145 / 0.52 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 180 / 0.19 | 180 / 0.325 | 180 / 0.405 | 180 / 0.48 | 180 / 0.55 | 180 / 0.685 | 180 / 0.815 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 160 / 0.19 | 160 / 0.325 | 160 / 0.405 | 160 / 0.48 | 160 / 0.55 | 160 / 0.685 | 160 / 0.815 | 413 |
| Art. 5525 coating FIRE | yes | 110 / 0.125 | 110 / 0.21 | 110 / 0.26 | 110 / 0.305 | 110 / 0.355 | 110 / 0.44 | 110 / 0.52 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 404 |
| Art. 6023 coating FIRE | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 406 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 403 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 110 / 0.24 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 100 / 0.24 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 105 / 0.12 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 105 / 0.12 | - | - | - | - | - | - | 393 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 90 / 0.24 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 100 / 0.15 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 100 / 0.15 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 100 / 0.09 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 100 / 0.09 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 100 / 0.135 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 180 / 0.19 | 180 / 0.325 | 180 / 0.405 | 180 / 0.48 | 180 / 0.55 | 180 / 0.685 | 180 / 0.815 | 412 |
| Art. 6499 coating FIRE | yes | 160 / 0.19 | 160 / 0.325 | 160 / 0.405 | 160 / 0.48 | 160 / 0.55 | 160 / 0.685 | 160 / 0.815 | 413 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 120 / 0.155 | 120 / 0.26 | 120 / 0.325 | 120 / 0.385 | 120 / 0.44 | 120 / 0.55 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 120 / 0.155 | 120 / 0.26 | 120 / 0.325 | 120 / 0.385 | 120 / 0.44 | 120 / 0.55 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 120 / 0.155 | 120 / 0.26 | 120 / 0.325 | 120 / 0.385 | 120 / 0.44 | 120 / 0.55 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.155 | 100 / 0.26 | 100 / 0.325 | 100 / 0.385 | 100 / 0.44 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.155 | 100 / 0.26 | 100 / 0.325 | 100 / 0.385 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 100 / 0.075 | 100 / 0.13 | 100 / 0.16 | 100 / 0.19 | 100 / 0.22 | 100 / 0.275 | 100 / 0.325 | 402 |
| Art. 8520 coating Signum | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 410 |
| Art. 8521 coating Signum | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 410 |
| Art. 8522 coating Signum | yes | 145 / 0.095 | 145 / 0.165 | 145 / 0.205 | 145 / 0.24 | 145 / 0.275 | 145 / 0.345 | 145 / 0.405 | 411 |
| Art. 8524 coating Signum | no | 130 / 0.155 | 130 / 0.26 | 130 / 0.325 | 130 / 0.385 | 130 / 0.44 | 130 / 0.55 | 130 / 0.65 | 405 |
| Art. 8620 coating Signum | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 410 |
| Art. 8621 coating Signum | yes | 145 / 0.155 | 145 / 0.26 | 145 / 0.325 | 145 / 0.385 | 145 / 0.44 | 145 / 0.55 | 145 / 0.65 | 410 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430).
Values are for the catalogue material group(s) shown, which cover the P40 Free-cutting steel sub-group; they are not tuned to 11SMn30. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1 | Plunging | 270 | 1xD | 1xD | 0.015 | 0.025 | 0.03 | 0.04 | 0.045 | 0.06 | 0.075 | 0.075 |
| P1.1.1 | Slotting | 270 | 1xD | 1xD | 0.02 | 0.025 | 0.035 | 0.05 | 0.06 | 0.08 | 0.1 | 0.1 |
| P1.1.1 | Roughing | 350 | 1.5xD | 0.4xD | 0.025 | 0.04 | 0.05 | 0.065 | 0.075 | 0.1 | 0.125 | 0.125 |
| P1.1.1 | Finishing | 540 | 2xD | 0.02xD | 0.02 | 0.035 | 0.045 | 0.055 | 0.065 | 0.09 | 0.11 | 0.11 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1 | HPC Roughing | Speed M | 260 | 3xD | 0.15xD | 0.04 | 0.06 | 0.08 | 0.095 | 0.115 | 0.155 | 0.195 | 0.195 |
| P1.1.1 | HSC Roughing | Speed M | 275 | 3xD | 0.1xD | 0.045 | 0.07 | 0.095 | 0.12 | 0.14 | 0.19 | 0.235 | 0.235 |
| P1.1.1 | HSC Finishing | Speed M | 290 | 3xD | 0.01xD | 0.02 | 0.03 | 0.04 | 0.05 | 0.06 | 0.075 | 0.095 | 0.095 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1 | Roughing | 315 | 0.1xD | 0.3xD | 0.01 | 0.019 | 0.039 | 0.058 | 0.08 | 0.115 | 0.155 | 0.195 | 0.235 |
| P1.1.1 | (Pre-)Finishing | 305 | 0.05xD | 0.1xD | 0.012 | 0.024 | 0.048 | 0.072 | 0.095 | 0.145 | 0.19 | 0.24 | 0.29 |
| P1.1.1 | Fine finishing | 315 | 0.01xD | 0.02xD | 0.01 | 0.021 | 0.042 | 0.063 | 0.085 | 0.125 | 0.17 | 0.21 | 0.25 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1 | Roughing | 220 | 0.05xD | 0.4xD | 0.008 | 0.017 | 0.034 | 0.051 | 0.07 | 0.1 | 0.135 | 0.17 | 0.2 |
| P1.1.1 | (Pre-)Finishing | 225 | 0.03xD | 0.25xD | 0.007 | 0.014 | 0.027 | 0.041 | 0.055 | 0.08 | 0.11 | 0.135 | 0.16 |
| P1.1.1 | Fine finishing | 235 | 0.01xD | 0.15xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1 | Roughing | 335 | 0.1xD | 0.1xD | 0.005 | 0.01 | 0.029 | 0.06 | 0.075 | 0.095 | 0.115 | 0.155 | 0.195 |
| P1.1.1 | (Pre-)Finishing | 265 | 0.03xD | 0.03xD | 0.003 | 0.006 | 0.018 | 0.035 | 0.045 | 0.06 | 0.07 | 0.095 | 0.12 |
| P1.1.1 | Fine finishing | 265 | 0.01xD | 0.01xD | 0.002 | 0.003 | 0.01 | 0.02 | 0.025 | 0.035 | 0.04 | 0.055 | 0.065 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Values are for the catalogue material group(s) shown, which cover the P40 Free-cutting steel sub-group; they are not tuned to 11SMn30.
One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.
Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.
| Material group | Column (hole type, substrate, coating) | Vc (m/min) | Taps | Catalogue page |
|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | through-holes, VHM, coating TiCN | 46 | Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944) | 966 |
Values are for the catalogue material group(s) shown, which cover the P40 Free-cutting steel sub-group; they are not tuned to 11SMn30.
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.
| Material group | Vc (m/min) | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 180 | 0.3 | 0.5 | 0.65 | 1.2 | 1.55 | 1.9 | 2.05 | 2.15 | 2.3 | 2.5 |
f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.
| Material group | Vc (m/min) | f Ø 14 | f Ø 16 | f Ø 18 | f Ø 20 | f Ø 22 | f Ø 24 | f Ø 28 | f Ø 32 | f Ø 38 | f Ø 42 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 180 | 2.15 | 2.3 | 2.4 | 2.5 | 2.6 | 2.7 | 2.9 | 3.05 | 3.25 | 3.4 |
f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.
| Material group | Vc (m/min) | f Ø 22 | f Ø 26 | f Ø 30 | f Ø 35 | f Ø 40 |
|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 30 | 1 | 1.05 | 1.1 | 1.2 | 1.25 |
f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.
| Material group | Vc (m/min) | f Ø 40 | f Ø 45 | f Ø 50 | f Ø 55 | f Ø 60 | f Ø 65 | f Ø 70 | f Ø 75 | f Ø 80 |
|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 30 | 1.25 | 1.3 | 1.35 | 1.45 | 1.5 | 1.55 | 1.6 | 1.6 | 1.65 |
f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 18 | 0.03 | 0.05 | 0.1 | 0.1 | 0.25 | 0.3 | 0.35 | 0.4 | 0.4 | 0.45 | 0.45 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 22 | 0.03 | 0.05 | 0.1 | 0.1 | 0.25 | 0.3 | 0.35 | 0.4 | 0.4 | 0.45 | 0.45 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 18 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 20 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB | 14 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
Values are for the catalogue material group(s) shown, which cover the P40 Free-cutting steel sub-group; they are not tuned to 11SMn30.
Coated carbide, P10–P25. Chip control is easy thanks to the manganese-sulfide inclusions.
The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO P grade list and in the grade chart.
EN 11SMn30, Werkstoffnummer 1.0715, US AISI 1213 / 1215 (nearest), JIS SUM22. The full table, with the nearest-match flags, is on the 11SMn30 / AISI 1213 cross-reference page.
Resulfurised free-machining steel: chips break themselves and speeds run high. The trade-off is weld and surface-integrity limits on the part, not the machining.
Are you overpaying on your 11SMn30 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
The published starting band for the P40 Free-cutting steel sub-group is 200–350 m/min (655–1150 sfm) at 0.10–0.40 mm/rev (.004–.016 ipr). It is a starting band for the whole sub-group, not a value tuned to 11SMn30, so confirm on a sample part and adjust for condition, tool and rigidity.
Coated carbide, P10–P25. Chip control is easy thanks to the manganese-sulfide inclusions. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.
EN 11SMn30 (Werkstoffnummer 1.0715); US: AISI 1213 / 1215 (nearest); JIS: SUM22. At least one pairing is nearest-by-properties, not a drop-in equivalent: the material certificate decides.
The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.