CUTTINGTOOLS / AI
Find equivalents

ISO P — Steel · P40

P40 — Free-cutting steel

Hardness range: 160–230 HB. Part of the ISO P — Steels group. Steel is the most widely machined material. Carbon and alloy steels are the target material for the majority of turning and milling operations. Hardness ranges from ~125 HB (low-carbon) to 350 HB (high-strength structural). CVD-coated carbide (TiCN/Al₂O₃ multilayer) dominates. Positive geometry for finishing, negative for heavy roughing.

Machining free-cutting steel? Find suitable carbide grades and understand why.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Picking an operation fills in the question. Edit it before you ask: add the tool type, diameter or hardness.

Material profile — P40

ISO designation
P40 (ISO P — Steels)
Material
Free-cutting steel
Hardness
160–230 HB
ISO group colour
Steel

Tooling guidance — P-group

Group summary
CVD-coated carbide at Vc 200–400 m/min. Positive geometry for finishing, negative for roughing.

Insert selection for free-cutting steel (12L14, 1215) — starting point

ISO application class
P (steel). Free-cutting steels (resulfurized or leaded) contain inclusions that break chips and lubricate the edge, so they run fast and clean. Match the ISO P class across brands rather than the brand name (Sandvik, Kennametal, Iscar, Walter, Seco and Mitsubishi each publish one), then confirm the exact grade for your condition.
Grade & coating
Coated carbide, P10–P25. Chip control is easy thanks to the manganese-sulfide inclusions.
Geometry
Positive sharp edge; chip control is rarely a problem on free-cutting grades.
Starting parameters
High speeds, Vc ≈ 200–350 m/min, fn ≈ 0.10–0.40 mm/rev. Confirm in the advisor or on a sample part.

Selection table: free-cutting steel (12L14, 1215)

OperationGeometryISO classCoating familyCoolantFirst check
RoughingPositive sharp edge; chip control is rarely a problemP10–P25Coated carbidePer processSpeed in band: built-up edge is the one common issue
FinishingPositive sharp edgeP10–P25Coated carbidePer processFinish drop with a dull edge: replace a worn edge
Interrupted cutPositive edge with a light honeP10–P25 (tougher end)Coated carbidePer processLead-free substitutes machine differently: re-tune speeds
Low rigidity / thin wallPositive sharp edgeP10–P25Coated carbidePer processMostly low speed or a dull edge

Check which of your current inserts are covered →

Drilling Free-cutting steel with solid carbide: published starting values

These are one manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use; start there, then adjust to your machine, setup rigidity, hole depth and coolant. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.

P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB (44 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no50 / 0.105------398
Art. 2469
coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65406
Art. 2471
Solid carbide drills, coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65403
Art. 2474
Solid carbide drills, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65404
Art. 2477
coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65406
Art. 2479
Solid carbide drills, coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65403
Art. 2719
Solid carbide drills, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65404
Art. 2996
Solid carbide drills, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65404
Art. 4044
coating FIRE
yes145 / 0.125145 / 0.21145 / 0.26145 / 0.305145 / 0.355145 / 0.44145 / 0.52408
Art. 4045
coating FIRE
yes145 / 0.125145 / 0.21145 / 0.26145 / 0.305145 / 0.355145 / 0.44145 / 0.52408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes180 / 0.19180 / 0.325180 / 0.405180 / 0.48180 / 0.55180 / 0.685180 / 0.815412
Art. 5499
Solid carbide drills, coating FIRE
yes160 / 0.19160 / 0.325160 / 0.405160 / 0.48160 / 0.55160 / 0.685160 / 0.815413
Art. 5525
coating FIRE
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44110 / 0.52409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65407
Art. 5651
Solid carbide drills, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65404
Art. 6023
coating FIRE
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes110 / 0.24------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no100 / 0.24------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes105 / 0.12------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes105 / 0.12------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no90 / 0.24------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes100 / 0.15------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes100 / 0.15------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes100 / 0.09------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes100 / 0.09------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes100 / 0.135------397
Art. 6498
coating FIRE
yes180 / 0.19180 / 0.325180 / 0.405180 / 0.48180 / 0.55180 / 0.685180 / 0.815412
Art. 6499
coating FIRE
yes160 / 0.19160 / 0.325160 / 0.405160 / 0.48160 / 0.55160 / 0.685160 / 0.815413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.155100 / 0.26100 / 0.325100 / 0.385100 / 0.44--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.155100 / 0.26100 / 0.325100 / 0.385---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes100 / 0.075100 / 0.13100 / 0.16100 / 0.19100 / 0.22100 / 0.275100 / 0.325402
Art. 8520
coating Signum
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65410
Art. 8521
coating Signum
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65410
Art. 8522
coating Signum
yes145 / 0.095145 / 0.165145 / 0.205145 / 0.24145 / 0.275145 / 0.345145 / 0.405411
Art. 8524
coating Signum
no130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65405
Art. 8620
coating Signum
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65410
Art. 8621
coating Signum
yes145 / 0.155145 / 0.26145 / 0.325145 / 0.385145 / 0.44145 / 0.55145 / 0.65410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430).

Turn Vc and f into rpm and feed rate →

Milling Free-cutting steel: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.1Plunging2701xD1xD0.0150.0250.030.040.0450.060.0750.075
P1.1.1Slotting2701xD1xD0.020.0250.0350.050.060.080.10.1
P1.1.1Roughing3501.5xD0.4xD0.0250.040.050.0650.0750.10.1250.125
P1.1.1Finishing5402xD0.02xD0.020.0350.0450.0550.0650.090.110.11

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.1HPC RoughingSpeed M2603xD0.15xD0.040.060.080.0950.1150.1550.1950.195
P1.1.1HSC RoughingSpeed M2753xD0.1xD0.0450.070.0950.120.140.190.2350.235
P1.1.1HSC FinishingSpeed M2903xD0.01xD0.020.030.040.050.060.0750.0950.095

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P1.1.1Roughing3150.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
P1.1.1(Pre-)Finishing3050.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
P1.1.1Fine finishing3150.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P1.1.1Roughing2200.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
P1.1.1(Pre-)Finishing2250.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
P1.1.1Fine finishing2350.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P1.1.1Roughing3350.1xD0.1xD0.0050.010.0290.060.0750.0950.1150.1550.195
P1.1.1(Pre-)Finishing2650.03xD0.03xD0.0030.0060.0180.0350.0450.060.070.0950.12
P1.1.1Fine finishing2650.01xD0.01xD0.0020.0030.010.020.0250.0350.040.0550.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Turn Vc and fz into rpm and feed rate →

Tapping Free-cutting steel with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HBthrough-holes, VHM, coating TiCN46Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944)966

Reaming Free-cutting steel: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

Scope: The catalogue has no separate group for free-cutting (resulphurised or leaded) steel. These values are for plain unalloyed steel, 0.15 % C, 125 HB, the nearest group; they were not published for 11SMn30, 12L14 or 1215.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB1800.30.50.651.21.551.92.052.152.32.5

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB1802.152.32.42.52.62.72.93.053.253.4

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB3011.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB301.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB180.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB220.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB180.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB200.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
P1.1.1: Unalloyed steel, annealed, 0.15 % C, Rm 420 N/mm², 125 HB140.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

free-cutting steel (12L14, 1215): what goes wrong, and what to check first

Built-up edge at low speed
The one common issue; raise the speed into the band.
Finish drop with a dull edge
Free-cutting steel finishes easily; replace a worn edge to keep it.
Lead-free substitutes machine differently
Bismuth or high-sulfur replacements for leaded steel behave a little differently; re-tune speeds.
Otherwise minimal
These grades are designed to machine; most problems are low speed or a dull edge.

Reference data

Frequently asked questions

What insert for free-cutting steel like 12L14?

A coated carbide, P10–P25; chip control is easy. Match the ISO P class across brands and confirm in the advisor.

Why is free-cutting steel so easy to machine?

Manganese-sulfide (and sometimes lead or bismuth) inclusions break chips and lubricate the edge, allowing high speeds and clean finishes.

What cutting speed for free-cutting steel?

High, roughly Vc 200–350 m/min, fn 0.10–0.40 mm/rev. Confirm on a sample part.

Do lead-free free-cutting steels machine the same?

Close, but bismuth or high-sulfur substitutes behave a little differently; re-tune speeds and watch chip formation.

Get cutting parameters for Free-cutting steel
The AI advisor maps your specific material condition and operation to a verified insert grade, coating, and Vc/fn range — with live search across the latest tooling catalogs. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your Free-cutting steel inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

Grade designations in this group

Each page cross-references the EN, Werkstoffnummer, AISI/UNS and JIS designations for one material, with the ISO machining group it falls in.

Related materials

Grades and designations catalogued at P40