Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for 16MnCr5 (W.-Nr. 1.7131). The numbers are the published P30 Case-hardened steel sub-group starting band; the designations are on the cross-reference page.
| Item | Value |
|---|---|
| ISO 513 group | P Steel |
| Sub-group | P30 Case-hardened steel |
| Sub-group hardness / condition | 58–62 HRC surface |
| Category | Case-hardening steel |
| EN / Werkstoffnummer | 16MnCr5 · 1.7131 |
Hardness is the range published for the whole P30 Case-hardened steel sub-group on our material guide; the delivery condition of your 16MnCr5 may sit anywhere inside it or outside it.
At least one designation of this material is a nearest commonly-cited counterpart, not a same-composition equivalent. The machining values below belong to the sub-group, so confirm the actual alloy and delivery condition on the material certificate.
| Condition | Vc m/min | Vc sfm | Feed mm/rev | Feed ipr |
|---|---|---|---|---|
| Soft state, carbide | 180–280 | 590–920 | see note | see note |
| Hardened case, CBN | 100–180 | 330–590 | 0.05–0.15 | .002–.006 |
Sub-group starting values for carbide inserts, from P30 Case-hardened steel. They describe the whole sub-group and are not tuned to 16MnCr5. The published feed for this sub-group is stated for the hardened-case (CBN) band only. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO P group range.
| Operation | Geometry | Coating family | Coolant | First check |
|---|---|---|---|---|
| Roughing | Soft pre-carburized state: normal turning geometry | Soft state: P-class CVD carbide | Per process | Confirm before or after carburizing first; it changes everything |
| Finishing | Hardened case: negative with chamfer plus hone, rigid setup | CBN or hard ceramic on the 58–62 HRC case | Run as hard turning | White layer on the case: keep the edge fresh, speed in band |
| Interrupted cut | Chamfered honed edge, rigid setup | CBN with a robust grade | Run as hard turning | Case-to-core transition shock: favour edge security |
| Low rigidity / thin wall | Rigid setup, negative geometry with chamfer plus hone for the case | As state of the part | Per state | Edge chipping cutting the hard case |
Setup rows are the selection table of the P30 Case-hardened steel guide. They carry no speeds, so they do not change the starting band above.
Same sub-group, same starting band: 20MnCr5
One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
Scope: Catalogue group P2.1.1 is annealed low-alloy steel at 180 HB: these values are for cutting before case hardening. Machining a hardened case (58-62 HRC) is a different job, see H10 and H20 hardened steel.
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 30 / 0.087 | - | - | - | - | - | - | 398 |
| Art. 1946 Solid carbide drills, coating TiAlN | no | 80 / 0.095 | 80 / 0.165 | 80 / 0.205 | 80 / 0.24 | 80 / 0.275 | 80 / 0.345 | 80 / 0.405 | 434 |
| Art. 2469 coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 404 |
| Art. 2477 coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 404 |
| Art. 4044 coating FIRE | yes | 120 / 0.095 | 120 / 0.165 | 120 / 0.205 | 120 / 0.24 | 120 / 0.275 | 120 / 0.345 | 120 / 0.405 | 408 |
| Art. 4045 coating FIRE | yes | 120 / 0.095 | 120 / 0.165 | 120 / 0.205 | 120 / 0.24 | 120 / 0.275 | 120 / 0.345 | 120 / 0.405 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 120 / 0.155 | 120 / 0.26 | 120 / 0.325 | 120 / 0.385 | 120 / 0.44 | 120 / 0.55 | 120 / 0.65 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 110 / 0.155 | 110 / 0.26 | 110 / 0.325 | 110 / 0.385 | 110 / 0.44 | 110 / 0.55 | 110 / 0.65 | 413 |
| Art. 5525 coating FIRE | yes | 110 / 0.095 | 110 / 0.165 | 110 / 0.205 | 110 / 0.24 | 110 / 0.275 | 110 / 0.345 | 110 / 0.405 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 404 |
| Art. 6023 coating FIRE | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 406 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 403 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 90 / 0.21 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 80 / 0.21 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 90 / 0.12 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 90 / 0.12 | - | - | - | - | - | - | 393 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 80 / 0.21 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 90 / 0.15 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 90 / 0.15 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 90 / 0.09 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 90 / 0.09 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 90 / 0.105 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 120 / 0.155 | 120 / 0.26 | 120 / 0.325 | 120 / 0.385 | 120 / 0.44 | 120 / 0.55 | 120 / 0.65 | 412 |
| Art. 6499 coating FIRE | yes | 110 / 0.155 | 110 / 0.26 | 110 / 0.325 | 110 / 0.385 | 110 / 0.44 | 110 / 0.55 | 110 / 0.65 | 413 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 110 / 0.125 | 110 / 0.21 | 110 / 0.26 | 110 / 0.305 | 110 / 0.355 | 110 / 0.44 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 110 / 0.125 | 110 / 0.21 | 110 / 0.26 | 110 / 0.305 | 110 / 0.355 | 110 / 0.44 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.125 | 100 / 0.21 | 100 / 0.26 | 100 / 0.305 | 100 / 0.355 | 100 / 0.44 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 80 / 0.06 | 80 / 0.105 | 80 / 0.13 | 80 / 0.155 | 80 / 0.175 | 80 / 0.22 | 80 / 0.26 | 402 |
| Art. 8520 coating Signum | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 410 |
| Art. 8521 coating Signum | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 410 |
| Art. 8522 coating Signum | yes | 120 / 0.095 | 120 / 0.165 | 120 / 0.205 | 120 / 0.24 | 120 / 0.275 | 120 / 0.345 | 120 / 0.405 | 411 |
| Art. 8524 coating Signum | no | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 405 |
| Art. 8620 coating Signum | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 410 |
| Art. 8621 coating Signum | yes | 120 / 0.125 | 120 / 0.21 | 120 / 0.26 | 120 / 0.305 | 120 / 0.355 | 120 / 0.44 | 120 / 0.52 | 410 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430, 434).
Values are for the catalogue material group(s) shown, which cover the P30 Case-hardened steel sub-group; they are not tuned to 16MnCr5. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
Scope: Catalogue group P2.1.1 is annealed low-alloy steel at 180 HB: these values are for cutting before case hardening. Machining a hardened case (58-62 HRC) is a different job, see H10 and H20 hardened steel.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | Plunging | 230 | 1xD | 1xD | 0.015 | 0.025 | 0.03 | 0.04 | 0.045 | 0.06 | 0.075 | 0.075 |
| P2.1.1 | Slotting | 230 | 1xD | 1xD | 0.02 | 0.025 | 0.035 | 0.05 | 0.06 | 0.08 | 0.1 | 0.1 |
| P2.1.1 | Roughing | 300 | 1.5xD | 0.4xD | 0.025 | 0.04 | 0.05 | 0.065 | 0.075 | 0.1 | 0.125 | 0.125 |
| P2.1.1 | Finishing | 460 | 2xD | 0.02xD | 0.02 | 0.035 | 0.045 | 0.055 | 0.065 | 0.09 | 0.11 | 0.11 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | HPC Roughing | Speed M | 235 | 3xD | 0.15xD | 0.035 | 0.055 | 0.07 | 0.09 | 0.105 | 0.145 | 0.18 | 0.18 |
| P2.1.1 | HSC Roughing | Speed M | 245 | 3xD | 0.1xD | 0.045 | 0.065 | 0.085 | 0.11 | 0.13 | 0.175 | 0.215 | 0.215 |
| P2.1.1 | HSC Finishing | Speed M | 255 | 3xD | 0.01xD | 0.02 | 0.025 | 0.035 | 0.045 | 0.055 | 0.07 | 0.09 | 0.09 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | Slotting | 285 | see ap table | 1xD | 0.031 | 0.062 | 0.092 | 0.125 | 0.185 | 0.245 | 0.35 | 0.42 | 0.56 |
| P2.1.1 | Roughing | 275 | see ap table | 0.6xD | 0.042 | 0.084 | 0.126 | 0.17 | 0.25 | 0.335 | 0.42 | 0.505 | 0.67 |
| P2.1.1 | (Pre-)Finishing | 285 | see ap table | 0.4xD | 0.035 | 0.07 | 0.105 | 0.14 | 0.21 | 0.28 | 0.35 | 0.42 | 0.56 |
ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:
| Material | Hardness | Ø 1 | Ø 2 | Ø 3 | Ø 4 | Ø 6 | Ø 8 | Ø 10 | Ø 12 | Ø 16 |
|---|---|---|---|---|---|---|---|---|---|---|
| P | less than 850 N/mm² | 0.06 | 0.12 | 0.18 | 0.24 | 0.36 | 0.48 | 0.6 | 0.72 | 0.96 |
| P | more than 850 N/mm² | 0.05 | 0.1 | 0.15 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.8 |
| M | less than 850 N/mm² | 0.04 | 0.08 | 0.12 | 0.16 | 0.24 | 0.32 | 0.4 | 0.48 | 0.64 |
| M | more than 850 N/mm² | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
| K | less than 240 HB | 0.06 | 0.12 | 0.18 | 0.24 | 0.36 | 0.48 | 0.6 | 0.72 | 0.96 |
| K | more than 240 HB | 0.05 | 0.1 | 0.15 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.8 |
| S | Ti alloys | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
| H | less than 55 HRC | 0.04 | 0.08 | 0.12 | 0.16 | 0.24 | 0.32 | 0.4 | 0.48 | 0.64 |
| H | 55-65 HRC | 0.03 | 0.07 | 0.1 | 0.12 | 0.18 | 0.24 | 0.3 | 0.36 | 0.48 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | Roughing | 285 | 0.1xD | 0.3xD | 0.01 | 0.019 | 0.039 | 0.058 | 0.08 | 0.115 | 0.155 | 0.195 | 0.235 |
| P2.1.1 | (Pre-)Finishing | 275 | 0.05xD | 0.1xD | 0.012 | 0.024 | 0.048 | 0.072 | 0.095 | 0.145 | 0.19 | 0.24 | 0.29 |
| P2.1.1 | Fine finishing | 285 | 0.01xD | 0.02xD | 0.01 | 0.021 | 0.042 | 0.063 | 0.085 | 0.125 | 0.17 | 0.21 | 0.25 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | Roughing | 195 | 0.05xD | 0.4xD | 0.008 | 0.017 | 0.034 | 0.051 | 0.07 | 0.1 | 0.135 | 0.17 | 0.2 |
| P2.1.1 | (Pre-)Finishing | 205 | 0.03xD | 0.25xD | 0.007 | 0.014 | 0.027 | 0.041 | 0.055 | 0.08 | 0.11 | 0.135 | 0.16 |
| P2.1.1 | Fine finishing | 210 | 0.01xD | 0.15xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1 | Roughing | 335 | 0.1xD | 0.1xD | 0.005 | 0.01 | 0.029 | 0.06 | 0.075 | 0.095 | 0.115 | 0.155 | 0.195 |
| P2.1.1 | (Pre-)Finishing | 265 | 0.03xD | 0.03xD | 0.003 | 0.006 | 0.018 | 0.035 | 0.045 | 0.06 | 0.07 | 0.095 | 0.12 |
| P2.1.1 | Fine finishing | 265 | 0.01xD | 0.01xD | 0.002 | 0.003 | 0.01 | 0.02 | 0.025 | 0.035 | 0.04 | 0.055 | 0.065 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Values are for the catalogue material group(s) shown, which cover the P30 Case-hardened steel sub-group; they are not tuned to 16MnCr5.
One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.
Scope: Catalogue group P2.1.1 is annealed low-alloy steel at 180 HB: these values are for cutting before case hardening. Machining a hardened case (58-62 HRC) is a different job, see H10 and H20 hardened steel.
| Material group | Column (hole type, substrate, coating) | Vc (m/min) | Taps | Catalogue page |
|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | through-holes, VHM, coating TiCN | 39 | Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944) | 966 |
Values are for the catalogue material group(s) shown, which cover the P30 Case-hardened steel sub-group; they are not tuned to 16MnCr5.
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
Scope: Catalogue group P2.1.1 is annealed low-alloy steel at 180 HB: these values are for cutting before case hardening. Machining a hardened case (58-62 HRC) is a different job, see H10 and H20 hardened steel.
| Material group | Vc (m/min) | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 180 | 0.3 | 0.45 | 0.6 | 1.15 | 1.45 | 1.75 | 1.9 | 2.05 | 2.15 | 2.35 |
f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.
| Material group | Vc (m/min) | f Ø 14 | f Ø 16 | f Ø 18 | f Ø 20 | f Ø 22 | f Ø 24 | f Ø 28 | f Ø 32 | f Ø 38 | f Ø 42 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 180 | 2.05 | 2.15 | 2.25 | 2.35 | 2.45 | 2.55 | 2.7 | 2.85 | 3.05 | 3.2 |
f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.
| Material group | Vc (m/min) | f Ø 22 | f Ø 26 | f Ø 30 | f Ø 35 | f Ø 40 |
|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 30 | 1 | 1.05 | 1.1 | 1.2 | 1.25 |
f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.
| Material group | Vc (m/min) | f Ø 40 | f Ø 45 | f Ø 50 | f Ø 55 | f Ø 60 | f Ø 65 | f Ø 70 | f Ø 75 | f Ø 80 |
|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 30 | 1.25 | 1.3 | 1.35 | 1.45 | 1.5 | 1.55 | 1.6 | 1.6 | 1.65 |
f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 14 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 18 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 14 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 16 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB | 12 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
Values are for the catalogue material group(s) shown, which cover the P30 Case-hardened steel sub-group; they are not tuned to 16MnCr5.
Soft pre-carburized state: P-class CVD carbide. Hardened case (58–62 HRC): CBN or hard ceramic, like hard turning, with a honed/chamfered edge.
The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO P grade list and in the grade chart.
EN 16MnCr5, Werkstoffnummer 1.7131, US AISI 5115 (nearest), JIS SCr415 (nearest). The full table, with the nearest-match flags, is on the 16MnCr5 / AISI 5115 cross-reference page.
Machined soft before carburising: gummy, prone to built-up edge, finish-critical on gear blanks. Sharp geometry and the upper half of the speed range keep it clean.
Are you overpaying on your 16MnCr5 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
The published starting band for the P30 Case-hardened steel sub-group is Soft state, carbide 180–280 m/min (590–920 sfm); Hardened case, CBN 100–180 m/min (330–590 sfm) at 0.05–0.15 mm/rev (.002–.006 ipr). It is a starting band for the whole sub-group, not a value tuned to 16MnCr5, so confirm on a sample part and adjust for condition, tool and rigidity.
Soft pre-carburized state: P-class CVD carbide. Hardened case (58–62 HRC): CBN or hard ceramic, like hard turning, with a honed/chamfered edge. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.
EN 16MnCr5 (Werkstoffnummer 1.7131); US: AISI 5115 (nearest); JIS: SCr415 (nearest). At least one pairing is nearest-by-properties, not a drop-in equivalent: the material certificate decides.
The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.