CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · N TIN BRONZE

CuSn8 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for CuSn8 (C52100). The numbers are the published N20 Copper / Brass sub-group starting band; the designations are on the cross-reference page.

ISO N · Non-ferrous N20 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

CuSn8: group, sub-group and condition

ItemValue
ISO 513 groupN Non-ferrous
Sub-groupN20 Copper / Brass
Sub-group hardness / condition80–160 HB
CategoryTin bronze
EN / WerkstoffnummerCuSn8 (CW453K) · 2.1030

Hardness is the range published for the whole N20 Copper / Brass sub-group on our material guide; the delivery condition of your CuSn8 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for CuSn8

ConditionVc m/minVc sfmFeed mm/revFeed ipr
Brass200–500655–16400.05–0.30.002–.012
Copper150–400490–13100.05–0.30.002–.012

Sub-group starting values for carbide inserts, from N20 Copper / Brass. They describe the whole sub-group and are not tuned to CuSn8. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO N group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingCopper: sharp high positive rake. Brass: near-neutral or slightly negative rakeUncoated polished carbide; PCD for high-volume workCoolant for copper to avoid smearingRake matched to the alloy: brass grabs, copper builds up
FinishingSharp edges throughoutUncoated polished carbideCoolant for copperSmearing: a dull or rubbing edge smears soft metal
Interrupted cutSharp edge, rake per alloyUncoated polished carbideCoolant for copperGrabbing or self-feeding on free-machining brass
Low rigidity / thin wallNear-neutral rake on brass to stop self-feedingUncoated polished carbideCoolant for copperLong stringy chips on copper: chipbreaker geometry

Setup rows are the selection table of the N20 Copper / Brass guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: CuZn39Pb3 · Cu-ETP

02b · DRILLING

Drilling CuSn8 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

N3.1.2: Copper and copper alloys: CuZn, CuSnZn (34 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no70 / 0.104------398
Art. 2469
coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44406
Art. 2471
Solid carbide drills, coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no95 / 0.0895 / 0.1495 / 0.1795 / 0.20595 / 0.23595 / 0.2995 / 0.345403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no95 / 0.0895 / 0.1495 / 0.1795 / 0.20595 / 0.23595 / 0.2995 / 0.345403
Art. 2474
Solid carbide drills, coating FIRE
no110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44404
Art. 2477
coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44406
Art. 2479
Solid carbide drills, coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no95 / 0.0895 / 0.1495 / 0.1795 / 0.20595 / 0.23595 / 0.2995 / 0.345403
Art. 2719
Solid carbide drills, coating FIRE
no110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44404
Art. 2996
Solid carbide drills, coating FIRE
no110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44404
Art. 4044
coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44408
Art. 4045
coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44408
Art. 5525
coating FIRE
yes110 / 0.08110 / 0.14110 / 0.17110 / 0.205110 / 0.235110 / 0.29110 / 0.345409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44407
Art. 5651
Solid carbide drills, coating FIRE
no110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44404
Art. 5768
Solid carbide drills with coolant ducts
yes135 / 0.105135 / 0.175135 / 0.22135 / 0.26135 / 0.3135 / 0.375135 / 0.44415
Art. 6023
coating FIRE
yes110 / 0.105110 / 0.175110 / 0.22110 / 0.26110 / 0.3110 / 0.375110 / 0.44406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no95 / 0.0895 / 0.1495 / 0.1795 / 0.20595 / 0.23595 / 0.2995 / 0.345403
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no105 / 0.153------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes130 / 0.128------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes130 / 0.128------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes130 / 0.076------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes130 / 0.076------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes110 / 0.089------397
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.105100 / 0.175100 / 0.22100 / 0.26100 / 0.3100 / 0.375-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.105100 / 0.175100 / 0.22100 / 0.26100 / 0.3100 / 0.375-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.105100 / 0.175100 / 0.22100 / 0.26100 / 0.3100 / 0.375-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.105100 / 0.175100 / 0.22100 / 0.26100 / 0.3--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.105100 / 0.175100 / 0.22100 / 0.26---430
Art. 6515yes120 / 0.105120 / 0.175120 / 0.22120 / 0.26120 / 0.3--425
Art. 6516
Ratio drills with coolant ducts
yes120 / 0.105120 / 0.175120 / 0.22120 / 0.26120 / 0.3--425
Art. 6517
Ratio drills with coolant ducts
yes120 / 0.105120 / 0.175120 / 0.22120 / 0.26120 / 0.3--425
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes100 / 0.08100 / 0.14100 / 0.17100 / 0.205100 / 0.235100 / 0.29100 / 0.345402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 415, 425, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the N20 Copper / Brass sub-group; they are not tuned to CuSn8. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling CuSn8: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N3.1.2HPC Roughing5 Speed3453xD0.2xD0.0350.050.0650.080.10.130.1650.165
N3.1.2HSC Roughing5 Speed3653xD0.15xD0.040.060.080.0950.1150.1550.1950.195
N3.1.2Finishing5 Speed4003xD0.02xD0.020.030.040.0550.0650.0850.1050.105

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

RF 100 A for unstable conditions (roughing end mill; catalogue page 703)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20fz Ø 25
N3.1.2Slotting2201xD1xD0.0090.010.020.0250.0350.040.0550.070.09
N3.1.2Roughing2551xD0.75xD0.0120.0150.0250.030.040.050.0650.080.1

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio roughing end mills Alu RF 100 A: Art. 6866, 6868, 6869, 6870, 6871, 6974, 6975, 6976, 6977. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

Diamond-coated milling cutters for fibre-reinforced plastics and graphite (slot drill, end mill, corner radius / torus, ball nose; catalogue page 704)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N3.1.2Slotting3001xD1xD0.0150.020.030.040.060.070.090.115
N3.1.2Roughing3451xD0.75xD0.020.0250.040.0550.0650.080.1050.13
N3.1.2Finishing6001xD0.02xD0.0190.0250.040.050.0650.0750.10.125

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: PCD slot drills (2-fluted): Art. 5492, 5493; PCD slot drills (3-fluted): Art. 5495, 5496; Kevlar end mills CR 100: Art. 6717, 6719, 6720; Slot drills XL (3-fluted): Art. 6721; Slot drills with corner radius (2-fluted): Art. 6722; End mills with corner radius (4-fluted): Art. 6723; Ball nose slot drills (2-fluted): Art. 6724; Ball nose end mills (4-fluted): Art. 6725; Kevlar end mills FR 100: Art. 6769, 6770, 6805, 6806. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
N3.1.2Roughing3600.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
N3.1.2(Pre-)Finishing3450.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
N3.1.2Fine finishing3600.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
N3.1.2Roughing2500.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
N3.1.2(Pre-)Finishing2550.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
N3.1.2Fine finishing2650.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
N3.1.2Roughing3200.1xD0.1xD0.0050.0090.0280.0550.0750.090.110.1450.185
N3.1.2(Pre-)Finishing2500.03xD0.03xD0.0030.0060.0170.0350.0450.0550.0650.090.11
N3.1.2Fine finishing2500.01xD0.01xD0.0020.0030.010.020.0250.030.040.050.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the N20 Copper / Brass sub-group; they are not tuned to CuSn8.

02e · REAMING

Reaming CuSn8: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
N3.1.2: Copper and copper alloys: CuZn, CuSnZn250.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
N3.1.2: Copper and copper alloys: CuZn, CuSnZn290.030.050.10.10.250.30.350.40.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
N3.1.2: Copper and copper alloys: CuZn, CuSnZn250.020.050.10.10.20.250.30.350.40.40.450.5

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
N3.1.2: Copper and copper alloys: CuZn, CuSnZn350.10.10.20.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
N3.1.2: Copper and copper alloys: CuZn, CuSnZn200.250.30.30.350.350.40.450.45

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the N20 Copper / Brass sub-group; they are not tuned to CuSn8.

03 · CARBIDE GRADES

Carbide grade class for CuSn8

Uncoated polished carbide; PCD for high-volume work. Sharp edges throughout.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO N grade list and in the grade chart.

04 · DESIGNATIONS

CuSn8 in EN, US and JIS terms

EN CuSn8 (CW453K), Werkstoffnummer 2.1030, US UNS C52100, JIS C5212. The full table, with the nearest-match flags, is on the CuSn8 / C52100 cross-reference page.

05 · NOTES

How CuSn8 behaves in the cut

Phosphor bronze: tougher and stringier than free-cutting brass, kinder than pure copper. Sharp geometry, moderate N-group data.

Cost check · free · brand-neutral

Are you overpaying on your CuSn8 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for CuSn8?

The published starting band for the N20 Copper / Brass sub-group is Brass 200–500 m/min (655–1640 sfm) at 0.05–0.30 mm/rev (.002–.012 ipr); Copper 150–400 m/min (490–1310 sfm) at 0.05–0.30 mm/rev (.002–.012 ipr). It is a starting band for the whole sub-group, not a value tuned to CuSn8, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for CuSn8?

Uncoated polished carbide; PCD for high-volume work. Sharp edges throughout. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is CuSn8 called in EN, US and JIS standards?

EN CuSn8 (CW453K) (Werkstoffnummer 2.1030); US: UNS C52100; JIS: C5212. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.