ISO N — Non-Ferrous · N20
N20 — Copper / Brass
Hardness range: 80–160 HB. Part of the ISO N — Non-Ferrous group. Non-ferrous metals (aluminium, copper, brass, magnesium) are soft and thermally conductive. Uncoated or DLC-coated fine-grain carbide with high positive rake, sharp edges, and polished flutes prevents built-up-edge. PCD inserts excel in high-volume aluminium production. No TiN/TiAlN coatings — aluminium welds to them.
Material profile — N20
- ISO designation
- N20 (ISO N — Non-Ferrous)
- Material
- Copper / Brass
- Hardness
- 80–160 HB
- ISO group colour
- Non-Ferrous
Tooling guidance — N-group
- Group summary
- Uncoated or DLC carbide for aluminium. Sharp edges, high positive rake, polished flutes prevent BUE.
Insert selection for copper / brass — starting point
- ISO application class
- N (non-ferrous). Free-machining brass cuts easily; copper is gummy and prone to built-up edge, so the two want different rake. Match the ISO N class across brands rather than the brand name (Sandvik, Kennametal, Iscar, Walter, Seco and Mitsubishi each publish one), then confirm the exact grade for your condition.
- Grade & coating
- Uncoated polished carbide; PCD for high-volume work. Sharp edges throughout.
- Geometry
- For copper, sharp high positive rake plus coolant to avoid smearing. For free-machining brass, a near-neutral or slightly negative rake stops the tool grabbing and self-feeding.
- Starting parameters
- Brass Vc ≈ 200–500 m/min; copper Vc ≈ 150–400 m/min; fn ≈ 0.05–0.30 mm/rev. Confirm in the advisor or on a sample part.
Selection table: copper / brass
| Operation | Geometry | ISO class | Coating family | Coolant | First check |
|---|---|---|---|---|---|
| Roughing | Copper: sharp high positive rake. Brass: near-neutral or slightly negative rake | N (N-class grade) | Uncoated polished carbide; PCD for high-volume work | Coolant for copper to avoid smearing | Rake matched to the alloy: brass grabs, copper builds up |
| Finishing | Sharp edges throughout | N (N-class grade) | Uncoated polished carbide | Coolant for copper | Smearing: a dull or rubbing edge smears soft metal |
| Interrupted cut | Sharp edge, rake per alloy | N (N-class grade) | Uncoated polished carbide | Coolant for copper | Grabbing or self-feeding on free-machining brass |
| Low rigidity / thin wall | Near-neutral rake on brass to stop self-feeding | N (N-class grade) | Uncoated polished carbide | Coolant for copper | Long stringy chips on copper: chipbreaker geometry |
Drilling Copper / Brass with solid carbide: published starting values
These are one manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use; start there, then adjust to your machine, setup rigidity, hole depth and coolant. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
N3.1.2: Copper and copper alloys: CuZn, CuSnZn (34 drill families)
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 70 / 0.104 | - | - | - | - | - | - | 398 |
| Art. 2469 coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 95 / 0.08 | 95 / 0.14 | 95 / 0.17 | 95 / 0.205 | 95 / 0.235 | 95 / 0.29 | 95 / 0.345 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 95 / 0.08 | 95 / 0.14 | 95 / 0.17 | 95 / 0.205 | 95 / 0.235 | 95 / 0.29 | 95 / 0.345 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 404 |
| Art. 2477 coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 95 / 0.08 | 95 / 0.14 | 95 / 0.17 | 95 / 0.205 | 95 / 0.235 | 95 / 0.29 | 95 / 0.345 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 404 |
| Art. 4044 coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 408 |
| Art. 4045 coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 408 |
| Art. 5525 coating FIRE | yes | 110 / 0.08 | 110 / 0.14 | 110 / 0.17 | 110 / 0.205 | 110 / 0.235 | 110 / 0.29 | 110 / 0.345 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 404 |
| Art. 5768 Solid carbide drills with coolant ducts | yes | 135 / 0.105 | 135 / 0.175 | 135 / 0.22 | 135 / 0.26 | 135 / 0.3 | 135 / 0.375 | 135 / 0.44 | 415 |
| Art. 6023 coating FIRE | yes | 110 / 0.105 | 110 / 0.175 | 110 / 0.22 | 110 / 0.26 | 110 / 0.3 | 110 / 0.375 | 110 / 0.44 | 406 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 95 / 0.08 | 95 / 0.14 | 95 / 0.17 | 95 / 0.205 | 95 / 0.235 | 95 / 0.29 | 95 / 0.345 | 403 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 105 / 0.153 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 130 / 0.128 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 130 / 0.128 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 130 / 0.076 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 130 / 0.076 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 110 / 0.089 | - | - | - | - | - | - | 397 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.105 | 100 / 0.175 | 100 / 0.22 | 100 / 0.26 | 100 / 0.3 | 100 / 0.375 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.105 | 100 / 0.175 | 100 / 0.22 | 100 / 0.26 | 100 / 0.3 | 100 / 0.375 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.105 | 100 / 0.175 | 100 / 0.22 | 100 / 0.26 | 100 / 0.3 | 100 / 0.375 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.105 | 100 / 0.175 | 100 / 0.22 | 100 / 0.26 | 100 / 0.3 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.105 | 100 / 0.175 | 100 / 0.22 | 100 / 0.26 | - | - | - | 430 |
| Art. 6515 | yes | 120 / 0.105 | 120 / 0.175 | 120 / 0.22 | 120 / 0.26 | 120 / 0.3 | - | - | 425 |
| Art. 6516 Ratio drills with coolant ducts | yes | 120 / 0.105 | 120 / 0.175 | 120 / 0.22 | 120 / 0.26 | 120 / 0.3 | - | - | 425 |
| Art. 6517 Ratio drills with coolant ducts | yes | 120 / 0.105 | 120 / 0.175 | 120 / 0.22 | 120 / 0.26 | 120 / 0.3 | - | - | 425 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 100 / 0.08 | 100 / 0.14 | 100 / 0.17 | 100 / 0.205 | 100 / 0.235 | 100 / 0.29 | 100 / 0.345 | 402 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 415, 425, 426, 427, 428, 429, 430).
Milling Copper / Brass: published starting values by tool and application
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
RF 100 Speed (end mill; catalogue pages 684, 685)
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | HPC Roughing | 5 Speed | 345 | 3xD | 0.2xD | 0.035 | 0.05 | 0.065 | 0.08 | 0.1 | 0.13 | 0.165 | 0.165 |
| N3.1.2 | HSC Roughing | 5 Speed | 365 | 3xD | 0.15xD | 0.04 | 0.06 | 0.08 | 0.095 | 0.115 | 0.155 | 0.195 | 0.195 |
| N3.1.2 | Finishing | 5 Speed | 400 | 3xD | 0.02xD | 0.02 | 0.03 | 0.04 | 0.055 | 0.065 | 0.085 | 0.105 | 0.105 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
RF 100 A for unstable conditions (roughing end mill; catalogue page 703)
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 | fz Ø 25 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | Slotting | 220 | 1xD | 1xD | 0.009 | 0.01 | 0.02 | 0.025 | 0.035 | 0.04 | 0.055 | 0.07 | 0.09 |
| N3.1.2 | Roughing | 255 | 1xD | 0.75xD | 0.012 | 0.015 | 0.025 | 0.03 | 0.04 | 0.05 | 0.065 | 0.08 | 0.1 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio roughing end mills Alu RF 100 A: Art. 6866, 6868, 6869, 6870, 6871, 6974, 6975, 6976, 6977. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
Diamond-coated milling cutters for fibre-reinforced plastics and graphite (slot drill, end mill, corner radius / torus, ball nose; catalogue page 704)
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | Slotting | 300 | 1xD | 1xD | 0.015 | 0.02 | 0.03 | 0.04 | 0.06 | 0.07 | 0.09 | 0.115 |
| N3.1.2 | Roughing | 345 | 1xD | 0.75xD | 0.02 | 0.025 | 0.04 | 0.055 | 0.065 | 0.08 | 0.105 | 0.13 |
| N3.1.2 | Finishing | 600 | 1xD | 0.02xD | 0.019 | 0.025 | 0.04 | 0.05 | 0.065 | 0.075 | 0.1 | 0.125 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: PCD slot drills (2-fluted): Art. 5492, 5493; PCD slot drills (3-fluted): Art. 5495, 5496; Kevlar end mills CR 100: Art. 6717, 6719, 6720; Slot drills XL (3-fluted): Art. 6721; Slot drills with corner radius (2-fluted): Art. 6722; End mills with corner radius (4-fluted): Art. 6723; Ball nose slot drills (2-fluted): Art. 6724; Ball nose end mills (4-fluted): Art. 6725; Kevlar end mills FR 100: Art. 6769, 6770, 6805, 6806. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | Roughing | 360 | 0.1xD | 0.3xD | 0.01 | 0.019 | 0.039 | 0.058 | 0.08 | 0.115 | 0.155 | 0.195 | 0.235 |
| N3.1.2 | (Pre-)Finishing | 345 | 0.05xD | 0.1xD | 0.012 | 0.024 | 0.048 | 0.072 | 0.095 | 0.145 | 0.19 | 0.24 | 0.29 |
| N3.1.2 | Fine finishing | 360 | 0.01xD | 0.02xD | 0.01 | 0.021 | 0.042 | 0.063 | 0.085 | 0.125 | 0.17 | 0.21 | 0.25 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | Roughing | 250 | 0.05xD | 0.4xD | 0.008 | 0.017 | 0.034 | 0.051 | 0.07 | 0.1 | 0.135 | 0.17 | 0.2 |
| N3.1.2 | (Pre-)Finishing | 255 | 0.03xD | 0.25xD | 0.007 | 0.014 | 0.027 | 0.041 | 0.055 | 0.08 | 0.11 | 0.135 | 0.16 |
| N3.1.2 | Fine finishing | 265 | 0.01xD | 0.15xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2 | Roughing | 320 | 0.1xD | 0.1xD | 0.005 | 0.009 | 0.028 | 0.055 | 0.075 | 0.09 | 0.11 | 0.145 | 0.185 |
| N3.1.2 | (Pre-)Finishing | 250 | 0.03xD | 0.03xD | 0.003 | 0.006 | 0.017 | 0.035 | 0.045 | 0.055 | 0.065 | 0.09 | 0.11 |
| N3.1.2 | Fine finishing | 250 | 0.01xD | 0.01xD | 0.002 | 0.003 | 0.01 | 0.02 | 0.025 | 0.03 | 0.04 | 0.05 | 0.065 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Reaming Copper / Brass: published starting values by reamer family
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
NC machine reamers, bright (solid carbide; catalogue page 1048)
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2: Copper and copper alloys: CuZn, CuSnZn | 25 | 0.03 | 0.05 | 0.1 | 0.1 | 0.25 | 0.3 | 0.35 | 0.4 | 0.4 | 0.45 | 0.45 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2: Copper and copper alloys: CuZn, CuSnZn | 29 | 0.03 | 0.05 | 0.1 | 0.1 | 0.25 | 0.3 | 0.35 | 0.4 | 0.4 | 0.45 | 0.45 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
Machine reamers (carbide (brazed); catalogue page 1050)
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| N3.1.2: Copper and copper alloys: CuZn, CuSnZn | 25 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.35 | 0.4 | 0.4 | 0.45 | 0.5 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
Machine reamers (carbide (brazed); catalogue page 1051)
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| N3.1.2: Copper and copper alloys: CuZn, CuSnZn | 35 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
Expanding machine reamers (carbide-tipped; catalogue page 1052)
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| N3.1.2: Copper and copper alloys: CuZn, CuSnZn | 20 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 | 0.45 | 0.45 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
copper / brass: what goes wrong, and what to check first
- Built-up edge on copper
- Copper is gummy and welds to the edge. Use a sharp positive polished edge and coolant; raise the speed.
- Grabbing / self-feeding on brass
- Too positive a rake lets free-machining brass pull the tool in. Use a near-neutral or slightly negative rake.
- Long stringy chips on copper
- Copper does not chip-break easily; use a sharp edge, coolant, and a chipbreaker geometry.
- Smearing / poor finish
- A dull or rubbing edge smears soft non-ferrous metal; keep the edge keen.
Reference data
Frequently asked questions
What insert for brass versus copper?
Both use sharp uncoated polished carbide, but brass wants a near-neutral or slightly negative rake to stop grabbing, while copper wants a sharp positive rake plus coolant. Match the ISO N class and confirm in the advisor.
Why does copper build up on the edge?
Copper is gummy and welds to the edge, especially at low speed. Use a sharp positive polished edge with coolant and raise the speed.
Why does brass grab the tool?
Free-machining brass with too positive a rake pulls the insert in and self-feeds; use a near-neutral or slightly negative rake.
What cutting speed for brass and copper?
Brass roughly Vc 200–500 m/min, copper Vc 150–400 m/min, fn 0.05–0.30 mm/rev. Confirm on a sample part.
Are you overpaying on your Copper / Brass inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
Grade designations in this group
Each page cross-references the EN, Werkstoffnummer, AISI/UNS and JIS designations for one material, with the ISO machining group it falls in.
Related materials
Grades and designations catalogued at N20