CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · M DUPLEX STAINLESS

Duplex 2205 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for Duplex 2205 (X2CrNiMoN22-5-3). The numbers are the published M10 Duplex stainless sub-group starting band; the designations are on the cross-reference page.

ISO M · Stainless steel M10 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

Duplex 2205: group, sub-group and condition

ItemValue
ISO 513 groupM Stainless steel
Sub-groupM10 Duplex stainless
Sub-group hardness / condition240–300 HB
CategoryDuplex stainless
EN / WerkstoffnummerX2CrNiMoN22-5-3 · 1.4462

Hardness is the range published for the whole M10 Duplex stainless sub-group on our material guide; the delivery condition of your Duplex 2205 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for Duplex 2205

ConditionVc m/minVc sfmFeed mm/revFeed ipr
M10 Duplex stainless, 240–300 HB80–150260–4900.10–0.30.004–.012

Sub-group starting values for carbide inserts, from M10 Duplex stainless. They describe the whole sub-group and are not tuned to Duplex 2205. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO M group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingPositive but robust honed edge; rigid setup for high cutting forcesTough PVD-coated carbideHigh-pressure coolant 15–20 barSevere work-hardening: keep DOC above the hardened layer
FinishingPositive, sharp but robust edgePVD-coated carbideHigh-pressure coolant 15–20 barBuilt-up edge at low speed: raise Vc into the duplex band
Interrupted cutRobust honed edgeTough PVD-coated carbideHigh-pressure coolant 15–20 barNotch wear at the depth-of-cut line: vary DOC
Low rigidity / thin wallRobust positive edge; shorten overhang, clamp rigidlyPVD-coated carbideHigh-pressure coolant 15–20 barDeflection and chatter: duplex pushes back

Setup rows are the selection table of the M10 Duplex stainless guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: Super duplex 2507

02b · DRILLING

Drilling Duplex 2205 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

M2.2.1: Duplex steel, high-strength stainless steels (37 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no15 / 0.038------398
Art. 2469
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14406
Art. 2471
Solid carbide drills, coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11403
Art. 2474
Solid carbide drills, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11404
Art. 2477
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14406
Art. 2479
Solid carbide drills, coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11403
Art. 2719
Solid carbide drills, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11404
Art. 2996
Solid carbide drills, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11404
Art. 4044
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14408
Art. 4045
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14408
Art. 5525
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14407
Art. 5651
Solid carbide drills, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11404
Art. 6023
coating FIRE
yes45 / 0.03545 / 0.05545 / 0.0745 / 0.0845 / 0.09545 / 0.11545 / 0.14406
Art. 6025
coating TiAlN nanoA
yes50 / 0.0550 / 0.0950 / 0.1150 / 0.1350 / 0.1550 / 0.18550 / 0.22414
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.09520 / 0.11403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes50 / 0.03------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no15 / 0.03------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes50 / 0.038------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes50 / 0.038------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no20 / 0.038------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes70 / 0.076------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes70 / 0.076------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes70 / 0.076------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes70 / 0.076------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes70 / 0.051------397
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes60 / 0.0460 / 0.0760 / 0.08560 / 0.10560 / 0.1260 / 0.145-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes50 / 0.0450 / 0.0750 / 0.08550 / 0.10550 / 0.1250 / 0.145-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes50 / 0.0450 / 0.0750 / 0.08550 / 0.10550 / 0.1250 / 0.145-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes50 / 0.0450 / 0.0750 / 0.08550 / 0.10550 / 0.12--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes50 / 0.03550 / 0.05550 / 0.0750 / 0.08---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes35 / 0.0435 / 0.0735 / 0.08535 / 0.10535 / 0.1235 / 0.14535 / 0.175402
Art. 8511
coating TiAlN nanoA
yes50 / 0.0550 / 0.0950 / 0.1150 / 0.1350 / 0.1550 / 0.18550 / 0.22414
Art. 8611
coating TiAlN nanoA
yes50 / 0.0550 / 0.0950 / 0.1150 / 0.1350 / 0.1550 / 0.18550 / 0.22414

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 406, 407, 408, 409, 414, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the M10 Duplex stainless sub-group; they are not tuned to Duplex 2205. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling Duplex 2205: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.2.1Plunging601xD1xD0.010.0150.020.0250.030.040.050.05
M2.2.1Slotting601xD1xD0.010.020.0250.0350.040.0550.070.07
M2.2.1Roughing901.5xD0.33xD0.020.0250.0350.0450.0550.0750.090.09
M2.2.1Finishing1202xD0.02xD0.0150.0250.030.040.0450.060.0750.075

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.2.1HPC Roughing5 Speed903xD0.1xD0.030.0450.060.0750.0950.1250.1550.155
M2.2.1HSC Roughing5 Speed953xD0.08xD0.0350.050.0650.0850.10.1350.170.17
M2.2.1Finishing5 Speed953xD0.02xD0.0150.020.0250.030.040.050.0650.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 65 HF (high-feed; catalogue page 705)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16
M2.2.1Slotting115see ap table1xD0.0230.0460.0690.090.140.1850.260.3150.42
M2.2.1Roughing100see ap table0.4xD0.0330.0660.0980.130.1950.260.330.3950.525
M2.2.1(Pre-)Finishing100see ap table0.3xD0.0260.0520.0790.1050.1550.210.260.3150.42

ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:

MaterialHardnessØ 1Ø 2Ø 3Ø 4Ø 6Ø 8Ø 10Ø 12Ø 16
Pless than 850 N/mm²0.060.120.180.240.360.480.60.720.96
Pmore than 850 N/mm²0.050.10.150.20.30.40.50.60.8
Mless than 850 N/mm²0.040.080.120.160.240.320.40.480.64
Mmore than 850 N/mm²0.030.070.10.120.180.240.30.360.48
Kless than 240 HB0.060.120.180.240.360.480.60.720.96
Kmore than 240 HB0.050.10.150.20.30.40.50.60.8
STi alloys0.030.070.10.120.180.240.30.360.48
Hless than 55 HRC0.040.080.120.160.240.320.40.480.64
H55-65 HRC0.030.070.10.120.180.240.30.360.48

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M2.2.1Roughing1150.06xD0.2xD0.0080.0170.0340.050.0650.10.1350.170.2
M2.2.1(Pre-)Finishing1000.02xD0.05xD0.0080.0170.0340.050.0650.10.1350.170.2
M2.2.1Fine finishing1000.01xD0.02xD0.0070.0150.0290.0440.060.090.1150.1450.175

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
M2.2.1Roughing850.04xD0.25xD0.0070.0140.0280.0420.0550.0850.1150.140.17
M2.2.1(Pre-)Finishing700.03xD0.2xD0.0050.0090.0190.0280.040.0550.0750.0950.115
M2.2.1Fine finishing800.01xD0.1xD0.0080.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
M2.2.1Roughing1150.1xD0.1xD0.0040.0070.0220.0450.060.070.0850.1150.145
M2.2.1(Pre-)Finishing900.02xD0.02xD0.0020.0040.0130.0250.0350.0450.0550.070.09
M2.2.1Fine finishing900.01xD0.01xD0.0010.0030.0080.0150.020.0250.030.040.05

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the M10 Duplex stainless sub-group; they are not tuned to Duplex 2205.

02e · REAMING

Reaming Duplex 2205: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.2.1: Duplex steel, high-strength stainless steels500.10.20.250.450.60.70.750.80.850.95

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
M2.2.1: Duplex steel, high-strength stainless steels500.80.850.90.95111.11.151.251.3

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
M2.2.1: Duplex steel, high-strength stainless steels1311.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
M2.2.1: Duplex steel, high-strength stainless steels131.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.2.1: Duplex steel, high-strength stainless steels40.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
M2.2.1: Duplex steel, high-strength stainless steels60.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
M2.2.1: Duplex steel, high-strength stainless steels40.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
M2.2.1: Duplex steel, high-strength stainless steels40.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
M2.2.1: Duplex steel, high-strength stainless steels40.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the M10 Duplex stainless sub-group; they are not tuned to Duplex 2205.

03 · CARBIDE GRADES

Carbide grade class for Duplex 2205

Tough PVD-coated carbide, a robust M-class grade. Duplex (2205 / 2507) is stronger and work-hardens harder than austenitic 304 / 316, so favour edge security over a keen finishing edge.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO M grade list and in the grade chart.

04 · DESIGNATIONS

Duplex 2205 in EN, US and JIS terms

EN X2CrNiMoN22-5-3, Werkstoffnummer 1.4462, US UNS S32205 / S31803. The full table, with the nearest-match flags, is on the Duplex 2205 / 1.4462 cross-reference page.

05 · NOTES

How X2CrNiMoN22-5-3 behaves in the cut

Twice the yield of 316L and severe work-hardening: forces are high, chips are strong, and rigidity is non-negotiable. Start at the bottom of the M range with a tough PVD grade.

Cost check · free · brand-neutral

Are you overpaying on your Duplex 2205 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for Duplex 2205?

The published starting band for the M10 Duplex stainless sub-group is 80–150 m/min (260–490 sfm) at 0.10–0.30 mm/rev (.004–.012 ipr). It is a starting band for the whole sub-group, not a value tuned to Duplex 2205, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for Duplex 2205?

Tough PVD-coated carbide, a robust M-class grade. Duplex (2205 / 2507) is stronger and work-hardens harder than austenitic 304 / 316, so favour edge security over a keen finishing edge. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is Duplex 2205 called in EN, US and JIS standards?

EN X2CrNiMoN22-5-3 (Werkstoffnummer 1.4462); US: UNS S32205 / S31803; JIS: none listed. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.