CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · K GREY CAST IRON

EN-GJL-200 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for EN-GJL-200 (W.-Nr. EN-JL1030). The numbers are the published K01 Grey cast iron (soft) sub-group starting band; the designations are on the cross-reference page.

ISO K · Cast iron K01 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

EN-GJL-200: group, sub-group and condition

ItemValue
ISO 513 groupK Cast iron
Sub-groupK01 Grey cast iron (soft)
Sub-group hardness / condition180–220 HB
CategoryGrey cast iron
EN / WerkstoffnummerEN-GJL-200 (GG20) · EN-JL1030

Hardness is the range published for the whole K01 Grey cast iron (soft) sub-group on our material guide; the delivery condition of your EN-GJL-200 may sit anywhere inside it or outside it.

NEAREST MATCH, NOT A TWIN

At least one designation of this material is a nearest commonly-cited counterpart, not a same-composition equivalent. The machining values below belong to the sub-group, so confirm the actual alloy and delivery condition on the material certificate.

02 · STARTING CUTTING DATA

Cutting speed and feed for EN-GJL-200

ConditionVc m/minVc sfmFeed mm/revFeed ipr
K01 Grey cast iron (soft), 180–220 HB150–350490–11500.10–0.50.004–.020

Sub-group starting values for carbide inserts, from K01 Grey cast iron (soft). They describe the whole sub-group and are not tuned to EN-GJL-200. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO K group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingNegative geometry, honed edge for cast skinCVD alumina (Al₂O₃)-coated carbideDry is acceptableAbrasive flank wear: keep the speed sensible
FinishingNegative geometry; short chips, no built-up edgeCVD alumina carbide; ceramic for high-speed finishingDry is acceptableFlank wear drifting the size
Interrupted cutHoned edge for cast skin and interruptionsCVD alumina carbideDry is acceptableEdge chipping on skin; ease into the first cut
Low rigidity / thin wallNegative geometry with a honed edge; support the partCVD alumina carbideDry is acceptableFrittering at the cut exit: reduce feed at exit

Setup rows are the selection table of the K01 Grey cast iron (soft) guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: EN-GJL-250

02b · DRILLING

Drilling EN-GJL-200 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB (39 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no60 / 0.105------398
Art. 768yes100 / 0.125100 / 0.21100 / 0.26100 / 0.305100 / 0.355100 / 0.44100 / 0.52418
Art. 773yes90 / 0.07590 / 0.1390 / 0.1690 / 0.1990 / 0.2290 / 0.27590 / 0.325424
Art. 1946
Solid carbide drills, coating TiAlN
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52434
Art. 2469
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65406
Art. 2471
Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52403
Art. 2474
Solid carbide drills, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52404
Art. 2477
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65406
Art. 2479
Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52403
Art. 2719
Solid carbide drills, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52404
Art. 2996
Solid carbide drills, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52404
Art. 4044
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65408
Art. 4045
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65412
Art. 5499
Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 5525
coating FIRE
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44110 / 0.52409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65407
Art. 5651
Solid carbide drills, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52404
Art. 6023
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52403
Art. 6068yes105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52421
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes150 / 0.33------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no130 / 0.33------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.18------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes150 / 0.18------393
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes140 / 0.18------397
Art. 6498
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65412
Art. 6499
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 6501
Solid carbide drills with coolant ducts, coating FIRE
yes130 / 0.19130 / 0.325130 / 0.405130 / 0.48130 / 0.55130 / 0.685130 / 0.815416
Art. 6502
coating FIRE
yes130 / 0.155130 / 0.26130 / 0.325130 / 0.385130 / 0.44130 / 0.55130 / 0.65417
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes105 / 0.155105 / 0.26105 / 0.325105 / 0.385105 / 0.44--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes105 / 0.155105 / 0.26105 / 0.325105 / 0.385---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes100 / 0.075100 / 0.13100 / 0.16100 / 0.19100 / 0.22100 / 0.275100 / 0.325402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 416, 417, 418, 421, 424, 426, 427, 428, 429, 430, 434).

Values are for the catalogue material group(s) shown, which cover the K01 Grey cast iron (soft) sub-group; they are not tuned to EN-GJL-200. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling EN-GJL-200: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.1.1Slotting1751xD1xD0.020.030.040.0550.070.090.1150.115
K1.1.1Roughing2001xD0.75xD0.0250.040.050.0650.080.1050.130.13
K1.1.1Finishing3501xD0.02xD0.0250.040.050.0650.0750.10.1250.125
K1.1.1Plunging1751xD1xD0.0150.0250.0350.0450.050.070.0850.085

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.1.1HPC RoughingSpeed P2353xD0.15xD0.040.060.080.10.1250.1650.2050.205
K1.1.1HSC RoughingSpeed P2453xD0.1xD0.050.0750.10.1250.150.20.250.25
K1.1.1FinishingSpeed P2553xD0.01xD0.020.030.040.050.060.080.10.1

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
K1.1.1Roughing2850.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
K1.1.1(Pre-)Finishing2750.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
K1.1.1Fine finishing2850.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
K1.1.1Roughing1950.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
K1.1.1(Pre-)Finishing2050.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
K1.1.1Fine finishing2100.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.1.1Roughing2550.1xD0.1xD0.0050.010.030.060.080.10.120.160.2
K1.1.1(Pre-)Finishing2000.02xD0.02xD0.0030.0060.0180.0350.050.060.0750.10.125
K1.1.1Fine finishing2000.01xD0.01xD0.0020.0040.0110.020.030.0350.040.0550.07

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the K01 Grey cast iron (soft) sub-group; they are not tuned to EN-GJL-200.

02d · TAPPING

Tapping EN-GJL-200 with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HBthrough- and blind holes, VHM, bright34Taps with coolant ducts for ISO metric threads (Art. 1858); Taps with coolant ducts for ISO metric fine threads (Art. 1861); Taps with coolant ducts for ISO metric threads (Art. 969); Taps with coolant ducts for ISO metric threads (Art. 1008); Taps with coolant ducts for ISO metric fine threads (Art. 972); Taps with coolant ducts for ISO metric fine threads (Art. 1009)968
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HBthrough- and blind holes, VHM, coating FIRE51Taps with coolant ducts for ISO metric threads (Art. 2311); Taps with coolant ducts for ISO metric threads (Art. 2506)968

Values are for the catalogue material group(s) shown, which cover the K01 Grey cast iron (soft) sub-group; they are not tuned to EN-GJL-200.

02e · REAMING

Reaming EN-GJL-200: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB800.250.350.50.91.151.41.551.651.71.9

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB801.651.71.81.91.952.052.152.32.452.55

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 Cast (solid carbide; catalogue page 1042)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB2000.550.751.351.752.152.32.452.62.85

f in mm/rev. Reamers this table belongs to: Art. 1036, Art. 1037.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB601.952.12.252.352.5

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB602.52.652.752.852.953.053.153.253.35

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB200.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB240.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB200.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB200.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
K1.1.1: Grey cast iron, pearlitic/ferritic, 180 HB200.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the K01 Grey cast iron (soft) sub-group; they are not tuned to EN-GJL-200.

03 · CARBIDE GRADES

Carbide grade class for EN-GJL-200

CVD alumina (Al₂O₃)-coated carbide, K10–K20: alumina resists the high-temperature abrasion of grey iron. Ceramic for high-speed finishing.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO K grade list and in the grade chart.

04 · DESIGNATIONS

EN-GJL-200 in EN, US and JIS terms

EN-GJL-200 (GG20), Werkstoffnummer EN-JL1030, US ASTM A48 Class 30 (nearest), JIS FC200. The full table, with the nearest-match flags, is on the EN-GJL-200 / A48 Class 30 cross-reference page.

05 · NOTES

How EN-GJL-200 behaves in the cut

Softer grey iron than GJL-250: short chips, abrasive skin, usually dry. The friendliest K-group cut; take the first pass under the cast skin.

Cost check · free · brand-neutral

Are you overpaying on your EN-GJL-200 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for EN-GJL-200?

The published starting band for the K01 Grey cast iron (soft) sub-group is 150–350 m/min (490–1150 sfm) at 0.10–0.50 mm/rev (.004–.020 ipr). It is a starting band for the whole sub-group, not a value tuned to EN-GJL-200, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for EN-GJL-200?

CVD alumina (Al₂O₃)-coated carbide, K10–K20: alumina resists the high-temperature abrasion of grey iron. Ceramic for high-speed finishing. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is EN-GJL-200 called in EN, US and JIS standards?

EN-GJL-200 (GG20) (Werkstoffnummer EN-JL1030); US: ASTM A48 Class 30 (nearest); JIS: FC200. At least one pairing is nearest-by-properties, not a drop-in equivalent: the material certificate decides.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.