CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Mitsubishi · ISO M

Mitsubishi MC7025

MC7025 is a Mitsubishi carbide insert grade (CVD), applied in the ISO M area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR, Kennametal, Sandvik, Seco, Walter. The manufacturer names a successor grade. 9 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 85 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Newer grade listed by the maker

Mitsubishi lists Mitsubishi MC7125 against MC7025 in its own documents. That is a maker-stated successor, not a discontinuation notice: see the source and what to check before switching →

Grade summary

Brand
Mitsubishi
Coating / substrate
CVD
ISO application area
M — stainless steel
Application range (catalog)
M15–M25
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Manufacturer-stated successor

Named by the manufacturer as the follow-up grade. Same brand, listed apart from other brands.

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • ISCAR IC6025 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Tungaloy AH630 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Seco TM2501 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • TaeguTec TT9225 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Kennametal KCM25B ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Walter WSM20S ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Sandvik GC2220 ISO M20 · 2+ independent charts (TaeguTec, Tungaloy)
  • Sandvik GC2025 ISO M20 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Korloy NC9125 ISO M20 · 1 chart (TaeguTec)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Kyocera CA6535 ISO M20 M30 · not verified
  • Kyocera PR1225 ISO M20 M30 · not verified · carbide
  • Kyocera PR1525 ISO M20 M30 · not verified
  • NTK DM4 ISO M20 M30 · not verified
  • NTK DT4 ISO M20 M30 · not verified

57 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

  • Kennametal KC5025 ISO M30 · not verified
  • Kennametal KCU25 ISO M30 · not verified
  • Kyocera PR1725 ISO M30 · not verified
  • Seco CP600 ISO M30 · not verified
  • Sumitomo AC1030U ISO M30 · not verified · carbide

9 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • MOLDINO IP100S ISO M20 · not verified
  • Sumitomo ACU2500 ISO M20 · not verified
  • ISCAR IC07 ISO M20 · not verified
  • ISCAR IC08 ISO M20 · not verified
  • ISCAR IC20 ISO M20 · not verified

4 more not shown.

Check MC7025 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Mitsubishi MC7025 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Mitsubishi MC7025 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
ISCAR IC6025 SUMO TEC® CVD SCMT09T308
Kennametal KCM25B MT-CVD TiCN/Al₂O₃ SCMT09T308
Sandvik GC2220 MT-CVD TiCN/Al₂O₃ SCMT09T308
Seco TM2501 Duratomic® CVD SCMT09T308
Walter WSM20S Tiger·tec® Silver PVD SCMT09T308

Insert designations using MC7025

DesignationGeometryCatalog codeApplication
SCMT09T308 90° Square · 7° clearance (positive) · 0.8mm Rε SCMT09T308 MC7025 M15–M25

Frequently asked questions

What is Mitsubishi MC7025?

MC7025 is a Mitsubishi carbide insert grade (CVD), applied in the ISO M area, used in 1 insert designation in this reference.

Which grades are direct peers of MC7025?

9 grades from other makers are listed in the same row of a manufacturer comparison chart as MC7025: ISCAR IC6025, Tungaloy AH630, Seco TM2501, TaeguTec TT9225, Kennametal KCM25B, Walter WSM20S, Sandvik GC2220, Sandvik GC2025, Korloy NC9125. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about MC7025
Cutting data for your material, when MC7025 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your MC7025 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where MC7025 is used: designations and materials