CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO M

ISCAR IC6025

IC6025 is a ISCAR carbide insert grade (SUMO TEC® CVD), applied in the ISO M area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by Kennametal, Mitsubishi, Sandvik, Seco, Walter. 8 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 45 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
SUMO TEC® CVD
ISO application area
M — stainless steel
Application range (catalog)
M15–M25
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Seco TM2501 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Mitsubishi MC7025 ISO M20 · 2+ independent charts (Mitsubishi Materials, TaeguTec)
  • Korloy NC9125 ISO M20 · 1 chart (TaeguTec)
  • Sandvik GC2025 ISO M20 · 1 chart (Ingersoll)
  • TaeguTec TT9225 ISO M20 · 1 chart (TaeguTec)
  • Kennametal KCM25B ISO M20 · 1 chart (TaeguTec)
  • Walter WSM20S ISO M20 · 1 chart (TaeguTec)
  • Tungaloy AH630 ISO M20 · 1 chart (TaeguTec)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Kennametal KC525M ISO M20 · not verified
  • Kyocera CA6525 ISO M20 · not verified
  • Kyocera PR1225 ISO M20 · not verified · carbide
  • Kyocera PR1525 ISO M20 · not verified
  • Kennametal K313 ISO M20 · not verified

40 more not shown.

Check IC6025 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC6025 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC6025 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
Kennametal KCM25B MT-CVD TiCN/Al₂O₃ SCMT09T308
Mitsubishi MC7025 CVD SCMT09T308
Sandvik GC2220 MT-CVD TiCN/Al₂O₃ SCMT09T308
Seco TM2501 Duratomic® CVD SCMT09T308
Walter WSM20S Tiger·tec® Silver PVD SCMT09T308

Insert designations using IC6025

DesignationGeometryCatalog codeApplication
SCMT09T308 90° Square · 7° clearance (positive) · 0.8mm Rε SCMT09T308 IC6025 M15–M25

Frequently asked questions

What is ISCAR IC6025?

IC6025 is a ISCAR carbide insert grade (SUMO TEC® CVD), applied in the ISO M area, used in 1 insert designation in this reference.

Which grades are direct peers of IC6025?

8 grades from other makers are listed in the same row of a manufacturer comparison chart as IC6025: Seco TM2501, Mitsubishi MC7025, Korloy NC9125, Sandvik GC2025, TaeguTec TT9225, Kennametal KCM25B, Walter WSM20S, Tungaloy AH630. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC6025
Cutting data for your material, when IC6025 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC6025 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC6025 is used: designations and materials