CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · K DUCTILE (NODULAR) IRON

ASTM A536 60-40-18 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for ASTM A536 60-40-18 (EN-GJS-400-15). The numbers are the published K20 Nodular / ductile iron sub-group starting band; the designations are on the cross-reference page.

ISO K · Cast iron K20 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

ASTM A536 60-40-18: group, sub-group and condition

ItemValue
ISO 513 groupK Cast iron
Sub-groupK20 Nodular / ductile iron
Sub-group hardness / condition170–260 HB
CategoryDuctile (nodular) iron
EN / WerkstoffnummerEN-GJS-400-15 (GGG40) · EN-JS1030

Hardness is the range published for the whole K20 Nodular / ductile iron sub-group on our material guide; the delivery condition of your ASTM A536 60-40-18 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for ASTM A536 60-40-18

ConditionVc m/minVc sfmFeed mm/revFeed ipr
K20 Nodular / ductile iron, 170–260 HB150–300490–9850.10–0.40.004–.016

Sub-group starting values for carbide inserts, from K20 Nodular / ductile iron. They describe the whole sub-group and are not tuned to ASTM A536 60-40-18. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO K group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingNegative geometry, honed edge for skin and scaleCVD alumina (Al₂O₃)-coated carbideDry or with coolantAbrasive flank wear: keep the speed sensible
FinishingNegative geometry, clean sharp-honed edgeCVD alumina carbideDry or with coolantBuilt-up edge at low speed: raise Vc into the band
Interrupted cutHoned edge for skin, scale and interruptionsSlightly tougher CVD alumina carbide than for grey ironDry or with coolantEdge chipping: tougher grade, ease into the cut
Low rigidity / thin wallNegative geometry; shorten overhang and support the partCVD alumina carbideDry or with coolantChatter is rigidity, not the grade

Setup rows are the selection table of the K20 Nodular / ductile iron guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: EN-GJS-600-3 · EN-GJS-700-2

02b · DRILLING

Drilling ASTM A536 60-40-18 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.

K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB (39 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no50 / 0.089------398
Art. 768yes85 / 0.10585 / 0.17585 / 0.2285 / 0.2685 / 0.385 / 0.37585 / 0.44418
Art. 773yes75 / 0.06575 / 0.1175 / 0.1475 / 0.16575 / 0.18575 / 0.23575 / 0.275424
Art. 1946
Solid carbide drills, coating TiAlN
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44434
Art. 2469
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555406
Art. 2471
Solid carbide drills, coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44403
Art. 2474
Solid carbide drills, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44404
Art. 2477
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555406
Art. 2479
Solid carbide drills, coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44403
Art. 2719
Solid carbide drills, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44404
Art. 2996
Solid carbide drills, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44404
Art. 4044
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555408
Art. 4045
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555412
Art. 5499
Solid carbide drills, coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555413
Art. 5525
coating FIRE
yes95 / 0.10595 / 0.17595 / 0.2295 / 0.2695 / 0.395 / 0.37595 / 0.44409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555407
Art. 5651
Solid carbide drills, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44404
Art. 6023
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no75 / 0.10575 / 0.17575 / 0.2275 / 0.2675 / 0.375 / 0.37575 / 0.44403
Art. 6068yes90 / 0.10590 / 0.17590 / 0.2290 / 0.2690 / 0.390 / 0.37590 / 0.44421
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes130 / 0.281------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no110 / 0.281------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes130 / 0.153------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes130 / 0.153------393
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes120 / 0.153------397
Art. 6498
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555412
Art. 6499
coating FIRE
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.46595 / 0.555413
Art. 6501
Solid carbide drills with coolant ducts, coating FIRE
yes110 / 0.165110 / 0.275110 / 0.345110 / 0.41110 / 0.47110 / 0.585110 / 0.69416
Art. 6502
coating FIRE
yes110 / 0.13110 / 0.22110 / 0.275110 / 0.325110 / 0.375110 / 0.465110 / 0.555417
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.13100 / 0.22100 / 0.275100 / 0.325100 / 0.375100 / 0.465-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.13100 / 0.22100 / 0.275100 / 0.325100 / 0.375100 / 0.465-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes95 / 0.1395 / 0.2295 / 0.27595 / 0.32595 / 0.37595 / 0.465-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.1390 / 0.2290 / 0.27590 / 0.32590 / 0.375--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.1390 / 0.2290 / 0.27590 / 0.325---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes85 / 0.06585 / 0.1185 / 0.1485 / 0.16585 / 0.18585 / 0.23585 / 0.275402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 416, 417, 418, 421, 424, 426, 427, 428, 429, 430, 434).

K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB (39 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no50 / 0.084------398
Art. 768yes80 / 0.180 / 0.16580 / 0.20580 / 0.24580 / 0.2880 / 0.3580 / 0.415418
Art. 773yes70 / 0.0670 / 0.10570 / 0.1370 / 0.15570 / 0.17570 / 0.2270 / 0.26424
Art. 1946
Solid carbide drills, coating TiAlN
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415434
Art. 2469
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52406
Art. 2471
Solid carbide drills, coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415403
Art. 2474
Solid carbide drills, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415404
Art. 2477
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52406
Art. 2479
Solid carbide drills, coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415403
Art. 2719
Solid carbide drills, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415404
Art. 2996
Solid carbide drills, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415404
Art. 4044
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52408
Art. 4045
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52412
Art. 5499
Solid carbide drills, coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52413
Art. 5525
coating FIRE
yes90 / 0.190 / 0.16590 / 0.20590 / 0.24590 / 0.2890 / 0.3590 / 0.415409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52407
Art. 5651
Solid carbide drills, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415404
Art. 6023
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no70 / 0.170 / 0.16570 / 0.20570 / 0.24570 / 0.2870 / 0.3570 / 0.415403
Art. 6068yes85 / 0.185 / 0.16585 / 0.20585 / 0.24585 / 0.2885 / 0.3585 / 0.415421
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes120 / 0.264------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no105 / 0.264------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes120 / 0.144------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes120 / 0.144------393
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes110 / 0.144------397
Art. 6498
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52412
Art. 6499
coating FIRE
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.4490 / 0.52413
Art. 6501
Solid carbide drills with coolant ducts, coating FIRE
yes105 / 0.155105 / 0.26105 / 0.325105 / 0.385105 / 0.44105 / 0.55105 / 0.65416
Art. 6502
coating FIRE
yes105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52417
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes95 / 0.12595 / 0.2195 / 0.2695 / 0.30595 / 0.35595 / 0.44-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes95 / 0.12595 / 0.2195 / 0.2695 / 0.30595 / 0.35595 / 0.44-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.35590 / 0.44-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes85 / 0.12585 / 0.2185 / 0.2685 / 0.30585 / 0.355--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes85 / 0.12585 / 0.2185 / 0.2685 / 0.305---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes80 / 0.0680 / 0.10580 / 0.1380 / 0.15580 / 0.17580 / 0.2280 / 0.26402

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 416, 417, 418, 421, 424, 426, 427, 428, 429, 430, 434).

Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to ASTM A536 60-40-18. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling ASTM A536 60-40-18: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.2.1, K1.2.2Slotting1751xD1xD0.020.030.040.0550.070.090.1150.115
K1.2.1, K1.2.2Roughing2001xD0.75xD0.0250.040.050.0650.080.1050.130.13
K1.2.1, K1.2.2Finishing3501xD0.02xD0.0250.040.050.0650.0750.10.1250.125
K1.2.1, K1.2.2Plunging1751xD1xD0.0150.0250.0350.0450.050.070.0850.085

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.2.1, K1.2.2HPC RoughingSpeed P2353xD0.15xD0.040.060.080.10.1250.1650.2050.205
K1.2.1, K1.2.2HSC RoughingSpeed P2453xD0.1xD0.050.0750.10.1250.150.20.250.25
K1.2.1, K1.2.2FinishingSpeed P2553xD0.01xD0.020.030.040.050.060.080.10.1

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
K1.2.1, K1.2.2Roughing2850.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
K1.2.1, K1.2.2(Pre-)Finishing2750.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
K1.2.1, K1.2.2Fine finishing2850.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
K1.2.1, K1.2.2Roughing1950.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
K1.2.1, K1.2.2(Pre-)Finishing2050.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
K1.2.1, K1.2.2Fine finishing2100.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
K1.2.1, K1.2.2Roughing2550.1xD0.1xD0.0050.010.030.060.080.10.120.160.2
K1.2.1, K1.2.2(Pre-)Finishing2000.02xD0.02xD0.0030.0060.0180.0350.050.060.0750.10.125
K1.2.1, K1.2.2Fine finishing2000.01xD0.01xD0.0020.0040.0110.020.030.0350.040.0550.07

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to ASTM A536 60-40-18.

02d · TAPPING

Tapping ASTM A536 60-40-18 with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HBthrough- and blind holes, VHM, bright34Taps with coolant ducts for ISO metric threads (Art. 1858); Taps with coolant ducts for ISO metric fine threads (Art. 1861); Taps with coolant ducts for ISO metric threads (Art. 969); Taps with coolant ducts for ISO metric threads (Art. 1008); Taps with coolant ducts for ISO metric fine threads (Art. 972); Taps with coolant ducts for ISO metric fine threads (Art. 1009)968
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HBthrough- and blind holes, VHM, bright34Taps with coolant ducts for ISO metric threads (Art. 1858); Taps with coolant ducts for ISO metric fine threads (Art. 1861); Taps with coolant ducts for ISO metric threads (Art. 969); Taps with coolant ducts for ISO metric threads (Art. 1008); Taps with coolant ducts for ISO metric fine threads (Art. 972); Taps with coolant ducts for ISO metric fine threads (Art. 1009)968
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HBthrough- and blind holes, VHM, coating FIRE51Taps with coolant ducts for ISO metric threads (Art. 2311); Taps with coolant ducts for ISO metric threads (Art. 2506)968
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HBthrough- and blind holes, VHM, coating FIRE51Taps with coolant ducts for ISO metric threads (Art. 2311); Taps with coolant ducts for ISO metric threads (Art. 2506)968

Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to ASTM A536 60-40-18.

02e · REAMING

Reaming ASTM A536 60-40-18: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB960.250.350.50.91.151.41.551.651.71.9
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB960.250.350.50.91.151.41.551.651.71.9

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB961.651.71.81.91.952.052.152.32.452.55
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB961.651.71.81.91.952.052.152.32.452.55

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 Cast (solid carbide; catalogue page 1042)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB2200.20.250.450.60.70.750.80.850.95
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB2200.20.250.450.60.70.750.80.850.95

f in mm/rev. Reamers this table belongs to: Art. 1036, Art. 1037.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB721.952.12.252.352.5
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB721.952.12.252.352.5

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB722.52.652.752.852.953.053.153.253.35
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB722.52.652.752.852.953.053.153.253.35

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB240.020.050.10.10.20.250.30.30.350.350.4
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB240.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB290.020.050.10.10.20.250.30.30.350.350.4
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB290.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB240.020.050.050.10.150.20.250.250.30.350.350.4
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB240.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB240.050.10.150.20.250.250.250.3
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB240.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB240.20.250.250.250.30.30.350.35
K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB240.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to ASTM A536 60-40-18.

03 · CARBIDE GRADES

Carbide grade class for ASTM A536 60-40-18

CVD alumina (Al₂O₃)-coated carbide, K10–K20, to resist high-temperature abrasion. Ductile iron is tougher than grey iron, so a slightly tougher edge than a grey-iron grade helps.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO K grade list and in the grade chart.

04 · DESIGNATIONS

ASTM A536 60-40-18 in EN, US and JIS terms

EN-GJS-400-15 (GGG40), Werkstoffnummer EN-JS1030, US ASTM A536 60-40-18, JIS FCD400. The full table, with the nearest-match flags, is on the EN-GJS-400-15 / A536 60-40-18 cross-reference page.

05 · NOTES

How EN-GJS-400-15 behaves in the cut

Ferritic ductile iron: tougher and stringier than grey iron, closer to steel in the cut. Lower half of the K range and a tougher edge line than you would pick for GJL.

Cost check · free · brand-neutral

Are you overpaying on your ASTM A536 60-40-18 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for ASTM A536 60-40-18?

The published starting band for the K20 Nodular / ductile iron sub-group is 150–300 m/min (490–985 sfm) at 0.10–0.40 mm/rev (.004–.016 ipr). It is a starting band for the whole sub-group, not a value tuned to ASTM A536 60-40-18, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for ASTM A536 60-40-18?

CVD alumina (Al₂O₃)-coated carbide, K10–K20, to resist high-temperature abrasion. Ductile iron is tougher than grey iron, so a slightly tougher edge than a grey-iron grade helps. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is ASTM A536 60-40-18 called in EN, US and JIS standards?

EN-GJS-400-15 (GGG40) (Werkstoffnummer EN-JS1030); US: ASTM A536 60-40-18; JIS: FCD400. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.