Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for EN-GJS-600-3 (W.-Nr. EN-JS1060). The numbers are the published K20 Nodular / ductile iron sub-group starting band; the designations are on the cross-reference page.
| Item | Value |
|---|---|
| ISO 513 group | K Cast iron |
| Sub-group | K20 Nodular / ductile iron |
| Sub-group hardness / condition | 170–260 HB |
| Category | Ductile (nodular) iron |
| EN / Werkstoffnummer | EN-GJS-600-3 (GGG60) · EN-JS1060 |
Hardness is the range published for the whole K20 Nodular / ductile iron sub-group on our material guide; the delivery condition of your EN-GJS-600-3 may sit anywhere inside it or outside it.
At least one designation of this material is a nearest commonly-cited counterpart, not a same-composition equivalent. The machining values below belong to the sub-group, so confirm the actual alloy and delivery condition on the material certificate.
| Condition | Vc m/min | Vc sfm | Feed mm/rev | Feed ipr |
|---|---|---|---|---|
| K20 Nodular / ductile iron, 170–260 HB | 150–300 | 490–985 | 0.10–0.40 | .004–.016 |
Sub-group starting values for carbide inserts, from K20 Nodular / ductile iron. They describe the whole sub-group and are not tuned to EN-GJS-600-3. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO K group range.
| Operation | Geometry | Coating family | Coolant | First check |
|---|---|---|---|---|
| Roughing | Negative geometry, honed edge for skin and scale | CVD alumina (Al₂O₃)-coated carbide | Dry or with coolant | Abrasive flank wear: keep the speed sensible |
| Finishing | Negative geometry, clean sharp-honed edge | CVD alumina carbide | Dry or with coolant | Built-up edge at low speed: raise Vc into the band |
| Interrupted cut | Honed edge for skin, scale and interruptions | Slightly tougher CVD alumina carbide than for grey iron | Dry or with coolant | Edge chipping: tougher grade, ease into the cut |
| Low rigidity / thin wall | Negative geometry; shorten overhang and support the part | CVD alumina carbide | Dry or with coolant | Chatter is rigidity, not the grade |
Setup rows are the selection table of the K20 Nodular / ductile iron guide. They carry no speeds, so they do not change the starting band above.
Same sub-group, same starting band: ASTM A536 60-40-18 · EN-GJS-700-2
One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 50 / 0.089 | - | - | - | - | - | - | 398 |
| Art. 768 | yes | 85 / 0.105 | 85 / 0.175 | 85 / 0.22 | 85 / 0.26 | 85 / 0.3 | 85 / 0.375 | 85 / 0.44 | 418 |
| Art. 773 | yes | 75 / 0.065 | 75 / 0.11 | 75 / 0.14 | 75 / 0.165 | 75 / 0.185 | 75 / 0.235 | 75 / 0.275 | 424 |
| Art. 1946 Solid carbide drills, coating TiAlN | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 434 |
| Art. 2469 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 404 |
| Art. 2477 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 404 |
| Art. 4044 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 408 |
| Art. 4045 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 413 |
| Art. 5525 coating FIRE | yes | 95 / 0.105 | 95 / 0.175 | 95 / 0.22 | 95 / 0.26 | 95 / 0.3 | 95 / 0.375 | 95 / 0.44 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 404 |
| Art. 6023 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 406 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 75 / 0.105 | 75 / 0.175 | 75 / 0.22 | 75 / 0.26 | 75 / 0.3 | 75 / 0.375 | 75 / 0.44 | 403 |
| Art. 6068 | yes | 90 / 0.105 | 90 / 0.175 | 90 / 0.22 | 90 / 0.26 | 90 / 0.3 | 90 / 0.375 | 90 / 0.44 | 421 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 130 / 0.281 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 110 / 0.281 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 130 / 0.153 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 130 / 0.153 | - | - | - | - | - | - | 393 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 120 / 0.153 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 412 |
| Art. 6499 coating FIRE | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | 95 / 0.555 | 413 |
| Art. 6501 Solid carbide drills with coolant ducts, coating FIRE | yes | 110 / 0.165 | 110 / 0.275 | 110 / 0.345 | 110 / 0.41 | 110 / 0.47 | 110 / 0.585 | 110 / 0.69 | 416 |
| Art. 6502 coating FIRE | yes | 110 / 0.13 | 110 / 0.22 | 110 / 0.275 | 110 / 0.325 | 110 / 0.375 | 110 / 0.465 | 110 / 0.555 | 417 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.13 | 100 / 0.22 | 100 / 0.275 | 100 / 0.325 | 100 / 0.375 | 100 / 0.465 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 100 / 0.13 | 100 / 0.22 | 100 / 0.275 | 100 / 0.325 | 100 / 0.375 | 100 / 0.465 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 95 / 0.13 | 95 / 0.22 | 95 / 0.275 | 95 / 0.325 | 95 / 0.375 | 95 / 0.465 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 90 / 0.13 | 90 / 0.22 | 90 / 0.275 | 90 / 0.325 | 90 / 0.375 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 90 / 0.13 | 90 / 0.22 | 90 / 0.275 | 90 / 0.325 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 85 / 0.065 | 85 / 0.11 | 85 / 0.14 | 85 / 0.165 | 85 / 0.185 | 85 / 0.235 | 85 / 0.275 | 402 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 416, 417, 418, 421, 424, 426, 427, 428, 429, 430, 434).
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 50 / 0.084 | - | - | - | - | - | - | 398 |
| Art. 768 | yes | 80 / 0.1 | 80 / 0.165 | 80 / 0.205 | 80 / 0.245 | 80 / 0.28 | 80 / 0.35 | 80 / 0.415 | 418 |
| Art. 773 | yes | 70 / 0.06 | 70 / 0.105 | 70 / 0.13 | 70 / 0.155 | 70 / 0.175 | 70 / 0.22 | 70 / 0.26 | 424 |
| Art. 1946 Solid carbide drills, coating TiAlN | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 434 |
| Art. 2469 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 404 |
| Art. 2477 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 404 |
| Art. 4044 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 408 |
| Art. 4045 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 413 |
| Art. 5525 coating FIRE | yes | 90 / 0.1 | 90 / 0.165 | 90 / 0.205 | 90 / 0.245 | 90 / 0.28 | 90 / 0.35 | 90 / 0.415 | 409 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 404 |
| Art. 6023 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 406 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 70 / 0.1 | 70 / 0.165 | 70 / 0.205 | 70 / 0.245 | 70 / 0.28 | 70 / 0.35 | 70 / 0.415 | 403 |
| Art. 6068 | yes | 85 / 0.1 | 85 / 0.165 | 85 / 0.205 | 85 / 0.245 | 85 / 0.28 | 85 / 0.35 | 85 / 0.415 | 421 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 120 / 0.264 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 105 / 0.264 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 120 / 0.144 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 120 / 0.144 | - | - | - | - | - | - | 393 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 110 / 0.144 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 412 |
| Art. 6499 coating FIRE | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | 90 / 0.52 | 413 |
| Art. 6501 Solid carbide drills with coolant ducts, coating FIRE | yes | 105 / 0.155 | 105 / 0.26 | 105 / 0.325 | 105 / 0.385 | 105 / 0.44 | 105 / 0.55 | 105 / 0.65 | 416 |
| Art. 6502 coating FIRE | yes | 105 / 0.125 | 105 / 0.21 | 105 / 0.26 | 105 / 0.305 | 105 / 0.355 | 105 / 0.44 | 105 / 0.52 | 417 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 95 / 0.125 | 95 / 0.21 | 95 / 0.26 | 95 / 0.305 | 95 / 0.355 | 95 / 0.44 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 95 / 0.125 | 95 / 0.21 | 95 / 0.26 | 95 / 0.305 | 95 / 0.355 | 95 / 0.44 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 90 / 0.125 | 90 / 0.21 | 90 / 0.26 | 90 / 0.305 | 90 / 0.355 | 90 / 0.44 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 85 / 0.125 | 85 / 0.21 | 85 / 0.26 | 85 / 0.305 | 85 / 0.355 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 85 / 0.125 | 85 / 0.21 | 85 / 0.26 | 85 / 0.305 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 80 / 0.06 | 80 / 0.105 | 80 / 0.13 | 80 / 0.155 | 80 / 0.175 | 80 / 0.22 | 80 / 0.26 | 402 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 397, 398, 402, 403, 404, 406, 407, 408, 409, 412, 413, 416, 417, 418, 421, 424, 426, 427, 428, 429, 430, 434).
Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to EN-GJS-600-3. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1, K1.2.2 | Slotting | 175 | 1xD | 1xD | 0.02 | 0.03 | 0.04 | 0.055 | 0.07 | 0.09 | 0.115 | 0.115 |
| K1.2.1, K1.2.2 | Roughing | 200 | 1xD | 0.75xD | 0.025 | 0.04 | 0.05 | 0.065 | 0.08 | 0.105 | 0.13 | 0.13 |
| K1.2.1, K1.2.2 | Finishing | 350 | 1xD | 0.02xD | 0.025 | 0.04 | 0.05 | 0.065 | 0.075 | 0.1 | 0.125 | 0.125 |
| K1.2.1, K1.2.2 | Plunging | 175 | 1xD | 1xD | 0.015 | 0.025 | 0.035 | 0.045 | 0.05 | 0.07 | 0.085 | 0.085 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1, K1.2.2 | HPC Roughing | Speed P | 235 | 3xD | 0.15xD | 0.04 | 0.06 | 0.08 | 0.1 | 0.125 | 0.165 | 0.205 | 0.205 |
| K1.2.1, K1.2.2 | HSC Roughing | Speed P | 245 | 3xD | 0.1xD | 0.05 | 0.075 | 0.1 | 0.125 | 0.15 | 0.2 | 0.25 | 0.25 |
| K1.2.1, K1.2.2 | Finishing | Speed P | 255 | 3xD | 0.01xD | 0.02 | 0.03 | 0.04 | 0.05 | 0.06 | 0.08 | 0.1 | 0.1 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1, K1.2.2 | Roughing | 285 | 0.1xD | 0.3xD | 0.01 | 0.019 | 0.039 | 0.058 | 0.08 | 0.115 | 0.155 | 0.195 | 0.235 |
| K1.2.1, K1.2.2 | (Pre-)Finishing | 275 | 0.05xD | 0.1xD | 0.012 | 0.024 | 0.048 | 0.072 | 0.095 | 0.145 | 0.19 | 0.24 | 0.29 |
| K1.2.1, K1.2.2 | Fine finishing | 285 | 0.01xD | 0.02xD | 0.01 | 0.021 | 0.042 | 0.063 | 0.085 | 0.125 | 0.17 | 0.21 | 0.25 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1, K1.2.2 | Roughing | 195 | 0.05xD | 0.4xD | 0.008 | 0.017 | 0.034 | 0.051 | 0.07 | 0.1 | 0.135 | 0.17 | 0.2 |
| K1.2.1, K1.2.2 | (Pre-)Finishing | 205 | 0.03xD | 0.25xD | 0.007 | 0.014 | 0.027 | 0.041 | 0.055 | 0.08 | 0.11 | 0.135 | 0.16 |
| K1.2.1, K1.2.2 | Fine finishing | 210 | 0.01xD | 0.15xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1, K1.2.2 | Roughing | 255 | 0.1xD | 0.1xD | 0.005 | 0.01 | 0.03 | 0.06 | 0.08 | 0.1 | 0.12 | 0.16 | 0.2 |
| K1.2.1, K1.2.2 | (Pre-)Finishing | 200 | 0.02xD | 0.02xD | 0.003 | 0.006 | 0.018 | 0.035 | 0.05 | 0.06 | 0.075 | 0.1 | 0.125 |
| K1.2.1, K1.2.2 | Fine finishing | 200 | 0.01xD | 0.01xD | 0.002 | 0.004 | 0.011 | 0.02 | 0.03 | 0.035 | 0.04 | 0.055 | 0.07 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to EN-GJS-600-3.
One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.
Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.
| Material group | Column (hole type, substrate, coating) | Vc (m/min) | Taps | Catalogue page |
|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | through- and blind holes, VHM, bright | 34 | Taps with coolant ducts for ISO metric threads (Art. 1858); Taps with coolant ducts for ISO metric fine threads (Art. 1861); Taps with coolant ducts for ISO metric threads (Art. 969); Taps with coolant ducts for ISO metric threads (Art. 1008); Taps with coolant ducts for ISO metric fine threads (Art. 972); Taps with coolant ducts for ISO metric fine threads (Art. 1009) | 968 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | through- and blind holes, VHM, bright | 34 | Taps with coolant ducts for ISO metric threads (Art. 1858); Taps with coolant ducts for ISO metric fine threads (Art. 1861); Taps with coolant ducts for ISO metric threads (Art. 969); Taps with coolant ducts for ISO metric threads (Art. 1008); Taps with coolant ducts for ISO metric fine threads (Art. 972); Taps with coolant ducts for ISO metric fine threads (Art. 1009) | 968 |
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | through- and blind holes, VHM, coating FIRE | 51 | Taps with coolant ducts for ISO metric threads (Art. 2311); Taps with coolant ducts for ISO metric threads (Art. 2506) | 968 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | through- and blind holes, VHM, coating FIRE | 51 | Taps with coolant ducts for ISO metric threads (Art. 2311); Taps with coolant ducts for ISO metric threads (Art. 2506) | 968 |
Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to EN-GJS-600-3.
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
Scope: Two catalogue groups: ferritic (160 HB, e.g. EN-GJS-400) and pearlitic (250 HB, e.g. EN-GJS-600/700). Use the table that matches your grade.
| Material group | Vc (m/min) | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 96 | 0.25 | 0.35 | 0.5 | 0.9 | 1.15 | 1.4 | 1.55 | 1.65 | 1.7 | 1.9 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 96 | 0.25 | 0.35 | 0.5 | 0.9 | 1.15 | 1.4 | 1.55 | 1.65 | 1.7 | 1.9 |
f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.
| Material group | Vc (m/min) | f Ø 14 | f Ø 16 | f Ø 18 | f Ø 20 | f Ø 22 | f Ø 24 | f Ø 28 | f Ø 32 | f Ø 38 | f Ø 42 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 96 | 1.65 | 1.7 | 1.8 | 1.9 | 1.95 | 2.05 | 2.15 | 2.3 | 2.45 | 2.55 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 96 | 1.65 | 1.7 | 1.8 | 1.9 | 1.95 | 2.05 | 2.15 | 2.3 | 2.45 | 2.55 |
f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 220 | 0.2 | 0.25 | 0.45 | 0.6 | 0.7 | 0.75 | 0.8 | 0.85 | 0.95 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 220 | 0.2 | 0.25 | 0.45 | 0.6 | 0.7 | 0.75 | 0.8 | 0.85 | 0.95 |
f in mm/rev. Reamers this table belongs to: Art. 1036, Art. 1037.
| Material group | Vc (m/min) | f Ø 22 | f Ø 26 | f Ø 30 | f Ø 35 | f Ø 40 |
|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 72 | 1.95 | 2.1 | 2.25 | 2.35 | 2.5 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 72 | 1.95 | 2.1 | 2.25 | 2.35 | 2.5 |
f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.
| Material group | Vc (m/min) | f Ø 40 | f Ø 45 | f Ø 50 | f Ø 55 | f Ø 60 | f Ø 65 | f Ø 70 | f Ø 75 | f Ø 80 |
|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 72 | 2.5 | 2.65 | 2.75 | 2.85 | 2.95 | 3.05 | 3.15 | 3.25 | 3.35 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 72 | 2.5 | 2.65 | 2.75 | 2.85 | 2.95 | 3.05 | 3.15 | 3.25 | 3.35 |
f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 24 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 24 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 29 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 29 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 24 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 24 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 24 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 24 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| K1.2.1: Cast iron with spheroidal graphite, ferritic, 160 HB | 24 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
| K1.2.2: Cast iron with spheroidal graphite, pearlitic, 250 HB | 24 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
Values are for the catalogue material group(s) shown, which cover the K20 Nodular / ductile iron sub-group; they are not tuned to EN-GJS-600-3.
CVD alumina (Al₂O₃)-coated carbide, K10–K20, to resist high-temperature abrasion. Ductile iron is tougher than grey iron, so a slightly tougher edge than a grey-iron grade helps.
The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO K grade list and in the grade chart.
EN-GJS-600-3 (GGG60), Werkstoffnummer EN-JS1060, US ASTM A536 80-55-06 (nearest), JIS FCD600. The full table, with the nearest-match flags, is on the EN-GJS-600-3 / A536 80-55-06 cross-reference page.
Pearlitic ductile iron: stronger, more abrasive, more heat. Data sits well below GJL-250 and flank wear is the life-limiter; a wear-resistant K-grade with a stable edge wins.
Are you overpaying on your EN-GJS-600-3 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
The published starting band for the K20 Nodular / ductile iron sub-group is 150–300 m/min (490–985 sfm) at 0.10–0.40 mm/rev (.004–.016 ipr). It is a starting band for the whole sub-group, not a value tuned to EN-GJS-600-3, so confirm on a sample part and adjust for condition, tool and rigidity.
CVD alumina (Al₂O₃)-coated carbide, K10–K20, to resist high-temperature abrasion. Ductile iron is tougher than grey iron, so a slightly tougher edge than a grey-iron grade helps. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.
EN-GJS-600-3 (GGG60) (Werkstoffnummer EN-JS1060); US: ASTM A536 80-55-06 (nearest); JIS: FCD600. At least one pairing is nearest-by-properties, not a drop-in equivalent: the material certificate decides.
The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.