Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for Inconel 625 (NiCr22Mo9Nb). The numbers are the published S20 Nickel superalloys (Inconel 718) sub-group starting band; the designations are on the cross-reference page.
| Item | Value |
|---|---|
| ISO 513 group | S Superalloys and titanium |
| Sub-group | S20 Nickel superalloys (Inconel 718) |
| Sub-group hardness / condition | 280–380 HB |
| Category | Nickel superalloy |
| EN / Werkstoffnummer | NiCr22Mo9Nb (Alloy 625) · 2.4856 |
Hardness is the range published for the whole S20 Nickel superalloys (Inconel 718) sub-group on our material guide; the delivery condition of your Inconel 625 may sit anywhere inside it or outside it.
| Condition | Vc m/min | Vc sfm | Feed mm/rev | Feed ipr |
|---|---|---|---|---|
| S20 Nickel superalloys (Inconel 718), 280–380 HB | 20–45 | 65–150 | 0.10–0.25 | .004–.010 |
Sub-group starting values for carbide inserts, from S20 Nickel superalloys (Inconel 718). They describe the whole sub-group and are not tuned to Inconel 625. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO S group range.
| Operation | Geometry | Coating family | Coolant | First check |
|---|---|---|---|---|
| Roughing | Positive but strong, honed edge; round or large-nose insert spreads heat | Tough fine-grain PVD carbide; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718 | High-pressure coolant essential | Depth-of-cut notch wear: vary DOC between passes |
| Finishing | Positive, honed edge; avoid fragile sharp corners | Tough fine-grain PVD carbide | High-pressure coolant essential | Rapid cratering and heat: coolant to the edge, hold Vc in band |
| Interrupted cut | Strong honed edge, round insert where possible | Tough fine-grain PVD carbide | High-pressure coolant essential | Edge chipping or built-up edge: sharp honed positive edge |
| Low rigidity / thin wall | Positive but strong edge; keep the tool moving | Tough fine-grain PVD carbide | High-pressure coolant essential | Work-hardened skin: keep DOC above the hardened layer |
Setup rows are the selection table of the S20 Nickel superalloys (Inconel 718) guide. They carry no speeds, so they do not change the starting band above.
Same sub-group, same starting band: Inconel 718 · Waspaloy
One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.
Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 15 / 0.06 | - | - | - | - | - | - | 398 |
| Art. 2469 coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 25 / 0.06 | 25 / 0.105 | 25 / 0.13 | 25 / 0.155 | 25 / 0.175 | 25 / 0.22 | 25 / 0.26 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 25 / 0.06 | 25 / 0.105 | 25 / 0.13 | 25 / 0.155 | 25 / 0.175 | 25 / 0.22 | 25 / 0.26 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 25 / 0.05 | 25 / 0.08 | 25 / 0.1 | 25 / 0.12 | 25 / 0.14 | 25 / 0.175 | 25 / 0.205 | 404 |
| Art. 2477 coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 25 / 0.06 | 25 / 0.105 | 25 / 0.13 | 25 / 0.155 | 25 / 0.175 | 25 / 0.22 | 25 / 0.26 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 25 / 0.05 | 25 / 0.08 | 25 / 0.1 | 25 / 0.12 | 25 / 0.14 | 25 / 0.175 | 25 / 0.205 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 25 / 0.05 | 25 / 0.08 | 25 / 0.1 | 25 / 0.12 | 25 / 0.14 | 25 / 0.175 | 25 / 0.205 | 404 |
| Art. 4044 coating FIRE | yes | 35 / 0.05 | 35 / 0.08 | 35 / 0.1 | 35 / 0.12 | 35 / 0.14 | 35 / 0.175 | 35 / 0.205 | 408 |
| Art. 4045 coating FIRE | yes | 35 / 0.05 | 35 / 0.08 | 35 / 0.1 | 35 / 0.12 | 35 / 0.14 | 35 / 0.175 | 35 / 0.205 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 35 / 0.05 | 35 / 0.08 | 35 / 0.1 | 35 / 0.12 | 35 / 0.14 | 35 / 0.175 | 35 / 0.205 | 413 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 25 / 0.05 | 25 / 0.08 | 25 / 0.1 | 25 / 0.12 | 25 / 0.14 | 25 / 0.175 | 25 / 0.205 | 404 |
| Art. 6023 coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 406 |
| Art. 6025 coating TiAlN nanoA | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 414 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 25 / 0.06 | 25 / 0.105 | 25 / 0.13 | 25 / 0.155 | 25 / 0.175 | 25 / 0.22 | 25 / 0.26 | 403 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 30 / 0.036 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 15 / 0.036 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 30 / 0.036 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 30 / 0.036 | - | - | - | - | - | - | 393 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 25 / 0.06 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 45 / 0.06 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 45 / 0.06 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 45 / 0.06 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 45 / 0.06 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 35 / 0.045 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 35 / 0.06 | 35 / 0.105 | 35 / 0.13 | 35 / 0.155 | 35 / 0.175 | 35 / 0.22 | 35 / 0.26 | 412 |
| Art. 6499 coating FIRE | yes | 35 / 0.05 | 35 / 0.08 | 35 / 0.1 | 35 / 0.12 | 35 / 0.14 | 35 / 0.175 | 35 / 0.205 | 413 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 35 / 0.04 | 35 / 0.065 | 35 / 0.08 | 35 / 0.095 | 35 / 0.11 | 35 / 0.135 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 35 / 0.04 | 35 / 0.065 | 35 / 0.08 | 35 / 0.095 | 35 / 0.11 | 35 / 0.135 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 35 / 0.04 | 35 / 0.065 | 35 / 0.08 | 35 / 0.095 | 35 / 0.11 | 35 / 0.135 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 35 / 0.04 | 35 / 0.065 | 35 / 0.08 | 35 / 0.095 | 35 / 0.11 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 35 / 0.04 | 35 / 0.065 | 35 / 0.08 | 35 / 0.095 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 25 / 0.05 | 25 / 0.08 | 25 / 0.1 | 25 / 0.12 | 25 / 0.14 | 25 / 0.175 | 25 / 0.205 | 402 |
| Art. 8511 coating TiAlN nanoA | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 414 |
| Art. 8520 coating Signum | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 410 |
| Art. 8521 coating Signum | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 410 |
| Art. 8522 coating Signum | yes | 40 / 0.05 | 40 / 0.08 | 40 / 0.1 | 40 / 0.12 | 40 / 0.14 | 40 / 0.175 | 40 / 0.205 | 411 |
| Art. 8524 coating Signum | no | 25 / 0.06 | 25 / 0.105 | 25 / 0.13 | 25 / 0.155 | 25 / 0.175 | 25 / 0.22 | 25 / 0.26 | 405 |
| Art. 8611 coating TiAlN nanoA | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 414 |
| Art. 8620 coating Signum | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 410 |
| Art. 8621 coating Signum | yes | 40 / 0.06 | 40 / 0.105 | 40 / 0.13 | 40 / 0.155 | 40 / 0.175 | 40 / 0.22 | 40 / 0.26 | 410 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 410, 411, 412, 413, 414, 426, 427, 428, 429, 430).
| Drill family | Internal coolant ducts | Ø 3 mm Vc / f | Ø 6 mm Vc / f | Ø 8 mm Vc / f | Ø 10 mm Vc / f | Ø 12 mm Vc / f | Ø 16 mm Vc / f | Ø 20 mm Vc / f | Catalogue page |
|---|---|---|---|---|---|---|---|---|---|
| Art. 701 Micro drills | no | 10 / 0.042 | - | - | - | - | - | - | 398 |
| Art. 2469 coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 406 |
| Art. 2471 Solid carbide drills, coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 407 |
| Art. 2472 Ratio drills without coolant ducts, coating FIRE | no | 15 / 0.045 | 15 / 0.075 | 15 / 0.09 | 15 / 0.105 | 15 / 0.125 | 15 / 0.155 | 15 / 0.18 | 403 |
| Art. 2473 Ratio drills without coolant ducts, coating FIRE | no | 15 / 0.045 | 15 / 0.075 | 15 / 0.09 | 15 / 0.105 | 15 / 0.125 | 15 / 0.155 | 15 / 0.18 | 403 |
| Art. 2474 Solid carbide drills, coating FIRE | no | 15 / 0.035 | 15 / 0.055 | 15 / 0.07 | 15 / 0.085 | 15 / 0.095 | 15 / 0.12 | 15 / 0.145 | 404 |
| Art. 2477 coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 406 |
| Art. 2479 Solid carbide drills, coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 407 |
| Art. 2480 Ratio drills without coolant ducts, coating FIRE | no | 15 / 0.045 | 15 / 0.075 | 15 / 0.09 | 15 / 0.105 | 15 / 0.125 | 15 / 0.155 | 15 / 0.18 | 403 |
| Art. 2719 Solid carbide drills, coating FIRE | no | 15 / 0.035 | 15 / 0.055 | 15 / 0.07 | 15 / 0.085 | 15 / 0.095 | 15 / 0.12 | 15 / 0.145 | 404 |
| Art. 2996 Solid carbide drills, coating FIRE | no | 15 / 0.035 | 15 / 0.055 | 15 / 0.07 | 15 / 0.085 | 15 / 0.095 | 15 / 0.12 | 15 / 0.145 | 404 |
| Art. 4044 coating FIRE | yes | 20 / 0.035 | 20 / 0.055 | 20 / 0.07 | 20 / 0.085 | 20 / 0.095 | 20 / 0.12 | 20 / 0.145 | 408 |
| Art. 4045 coating FIRE | yes | 20 / 0.035 | 20 / 0.055 | 20 / 0.07 | 20 / 0.085 | 20 / 0.095 | 20 / 0.12 | 20 / 0.145 | 408 |
| Art. 5498 Ratio drills with coolant ducts, coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 412 |
| Art. 5499 Solid carbide drills, coating FIRE | yes | 20 / 0.035 | 20 / 0.055 | 20 / 0.07 | 20 / 0.085 | 20 / 0.095 | 20 / 0.12 | 20 / 0.145 | 413 |
| Art. 5650 RT 100 U Solid carbide drills, coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 407 |
| Art. 5651 Solid carbide drills, coating FIRE | no | 15 / 0.035 | 15 / 0.055 | 15 / 0.07 | 15 / 0.085 | 15 / 0.095 | 15 / 0.12 | 15 / 0.145 | 404 |
| Art. 6023 coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 406 |
| Art. 6025 coating TiAlN nanoA | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 414 |
| Art. 6026 Ratio drills without coolant ducts, coating FIRE | no | 15 / 0.045 | 15 / 0.075 | 15 / 0.09 | 15 / 0.105 | 15 / 0.125 | 15 / 0.155 | 15 / 0.18 | 403 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN | yes | 20 / 0.025 | - | - | - | - | - | - | 392 |
| Art. 6405 ExclusiveLine Micro drills, coating TiAlN SuperA | no | 10 / 0.025 | - | - | - | - | - | - | 392 |
| Art. 6408 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 20 / 0.025 | - | - | - | - | - | - | 393 |
| Art. 6412 ExclusiveLine Micro drills, coating TiAlN SuperA | yes | 20 / 0.025 | - | - | - | - | - | - | 393 |
| Art. 6487 ExclusiveLine Micro drills, coating Perrox | no | 15 / 0.042 | - | - | - | - | - | - | 394 |
| Art. 6488 ExclusiveLine Micro drills, coating Perrox | yes | 30 / 0.042 | - | - | - | - | - | - | 395 |
| Art. 6489 ExclusiveLine Micro drills, coating Perrox | yes | 30 / 0.042 | - | - | - | - | - | - | 395 |
| Art. 6490 ExclusiveLine Micro drills, coating Perrox | yes | 30 / 0.042 | - | - | - | - | - | - | 396 |
| Art. 6491 ExclusiveLine Micro drills, coating Perrox | yes | 30 / 0.042 | - | - | - | - | - | - | 396 |
| Art. 6493 ExclusiveLine Micro drills, coating Ferrox | yes | 20 / 0.032 | - | - | - | - | - | - | 397 |
| Art. 6498 coating FIRE | yes | 20 / 0.045 | 20 / 0.075 | 20 / 0.09 | 20 / 0.105 | 20 / 0.125 | 20 / 0.155 | 20 / 0.18 | 412 |
| Art. 6499 coating FIRE | yes | 20 / 0.035 | 20 / 0.055 | 20 / 0.07 | 20 / 0.085 | 20 / 0.095 | 20 / 0.12 | 20 / 0.145 | 413 |
| Art. 6509 Ratio drills with coolant ducts, coating TiAlN | yes | 20 / 0.025 | 20 / 0.045 | 20 / 0.055 | 20 / 0.065 | 20 / 0.075 | 20 / 0.095 | - | 426 |
| Art. 6511 Ratio drills with coolant ducts, coating TiAlN | yes | 20 / 0.025 | 20 / 0.045 | 20 / 0.055 | 20 / 0.065 | 20 / 0.075 | 20 / 0.095 | - | 427 |
| Art. 6512 Ratio drills with coolant ducts, coating TiAlN | yes | 20 / 0.025 | 20 / 0.045 | 20 / 0.055 | 20 / 0.065 | 20 / 0.075 | 20 / 0.095 | - | 428 |
| Art. 6513 Ratio drills with coolant ducts, coating TiAlN | yes | 20 / 0.025 | 20 / 0.045 | 20 / 0.055 | 20 / 0.065 | 20 / 0.075 | - | - | 429 |
| Art. 6514 Ratio drills with coolant ducts, coating TiAlN | yes | 20 / 0.025 | 20 / 0.045 | 20 / 0.055 | 20 / 0.065 | - | - | - | 430 |
| Art. 6596 Pilot drills with coolant ducts, coating FIRE | yes | 15 / 0.035 | 15 / 0.055 | 15 / 0.07 | 15 / 0.085 | 15 / 0.095 | 15 / 0.12 | 15 / 0.145 | 402 |
| Art. 8511 coating TiAlN nanoA | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 414 |
| Art. 8520 coating Signum | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 410 |
| Art. 8521 coating Signum | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 410 |
| Art. 8522 coating Signum | yes | 25 / 0.035 | 25 / 0.055 | 25 / 0.07 | 25 / 0.085 | 25 / 0.095 | 25 / 0.12 | 25 / 0.145 | 411 |
| Art. 8524 coating Signum | no | 15 / 0.045 | 15 / 0.075 | 15 / 0.09 | 15 / 0.105 | 15 / 0.125 | 15 / 0.155 | 15 / 0.18 | 405 |
| Art. 8611 coating TiAlN nanoA | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 414 |
| Art. 8620 coating Signum | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 410 |
| Art. 8621 coating Signum | yes | 25 / 0.045 | 25 / 0.075 | 25 / 0.09 | 25 / 0.105 | 25 / 0.125 | 25 / 0.155 | 25 / 0.18 | 410 |
Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 410, 411, 412, 413, 414, 426, 427, 428, 429, 430).
Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 625. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.
One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.
Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.
| Material group | Application | Type | Vc (m/min) | ap max | ae max | fz Ø 4 | fz Ø 5 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3 | HPC Roughing | 7 Speed | 30 | 3xD | 0.08xD | 0.03 | 0.04 | 0.055 | 0.07 | 0.085 | 0.11 | 0.14 | 0.14 |
| S1.1.3 | HSC Roughing | 7 Speed | 30 | 3xD | 0.05xD | 0.03 | 0.04 | 0.055 | 0.07 | 0.085 | 0.11 | 0.14 | 0.14 |
| S1.1.3 | Finishing | 7 Speed | 30 | 3xD | 0.01xD | 0.01 | 0.015 | 0.02 | 0.025 | 0.03 | 0.04 | 0.05 | 0.05 |
| S1.1.4 | HPC Roughing | 7 Speed | 20 | 3xD | 0.08xD | 0.025 | 0.04 | 0.055 | 0.065 | 0.08 | 0.105 | 0.13 | 0.13 |
| S1.1.4 | HSC Roughing | 7 Speed | 20 | 3xD | 0.05xD | 0.025 | 0.04 | 0.055 | 0.065 | 0.08 | 0.105 | 0.13 | 0.13 |
| S1.1.4 | Finishing | 7 Speed | 20 | 3xD | 0.01xD | 0.01 | 0.015 | 0.02 | 0.025 | 0.03 | 0.04 | 0.05 | 0.05 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3 | Roughing | 40 | 0.06xD | 0.2xD | 0.008 | 0.016 | 0.031 | 0.047 | 0.065 | 0.095 | 0.125 | 0.155 | 0.19 |
| S1.1.3 | (Pre-)Finishing | 35 | 0.02xD | 0.05xD | 0.008 | 0.016 | 0.031 | 0.047 | 0.065 | 0.095 | 0.125 | 0.155 | 0.19 |
| S1.1.3 | Fine finishing | 35 | 0.01xD | 0.02xD | 0.007 | 0.014 | 0.027 | 0.041 | 0.055 | 0.08 | 0.11 | 0.135 | 0.165 |
| S1.1.4 | Roughing | 30 | 0.06xD | 0.2xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
| S1.1.4 | (Pre-)Finishing | 25 | 0.02xD | 0.05xD | 0.007 | 0.015 | 0.03 | 0.045 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 |
| S1.1.4 | Fine finishing | 25 | 0.01xD | 0.02xD | 0.007 | 0.013 | 0.026 | 0.039 | 0.05 | 0.08 | 0.105 | 0.13 | 0.155 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 2 | fz Ø 3 | fz Ø 4 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3 | Roughing | 30 | 0.04xD | 0.25xD | 0.007 | 0.013 | 0.027 | 0.04 | 0.055 | 0.08 | 0.105 | 0.135 | 0.16 |
| S1.1.3 | (Pre-)Finishing | 25 | 0.03xD | 0.2xD | 0.005 | 0.01 | 0.019 | 0.029 | 0.04 | 0.06 | 0.08 | 0.095 | 0.115 |
| S1.1.3 | Fine finishing | 30 | 0.01xD | 0.1xD | 0.007 | 0.014 | 0.028 | 0.042 | 0.055 | 0.085 | 0.115 | 0.14 | 0.17 |
| S1.1.4 | Roughing | 25 | 0.04xD | 0.25xD | 0.006 | 0.013 | 0.025 | 0.038 | 0.05 | 0.075 | 0.1 | 0.125 | 0.15 |
| S1.1.4 | (Pre-)Finishing | 20 | 0.03xD | 0.2xD | 0.005 | 0.009 | 0.018 | 0.028 | 0.035 | 0.055 | 0.075 | 0.09 | 0.11 |
| S1.1.4 | Fine finishing | 20 | 0.01xD | 0.1xD | 0.007 | 0.013 | 0.027 | 0.04 | 0.055 | 0.08 | 0.105 | 0.135 | 0.16 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
| Material group | Application | Vc (m/min) | ap max | ae max | fz Ø 0.5 | fz Ø 1 | fz Ø 3 | fz Ø 6 | fz Ø 8 | fz Ø 10 | fz Ø 12 | fz Ø 16 | fz Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3 | Roughing | 30 | 0.1xD | 0.1xD | 0.003 | 0.006 | 0.019 | 0.04 | 0.05 | 0.065 | 0.075 | 0.1 | 0.125 |
| S1.1.3 | (Pre-)Finishing | 25 | 0.02xD | 0.02xD | 0.002 | 0.004 | 0.012 | 0.025 | 0.03 | 0.04 | 0.045 | 0.06 | 0.075 |
| S1.1.3 | Fine finishing | 25 | 0.01xD | 0.01xD | 0.001 | 0.002 | 0.007 | 0.015 | 0.02 | 0.02 | 0.025 | 0.035 | 0.045 |
| S1.1.4 | Roughing | 25 | 0.1xD | 0.1xD | 0.003 | 0.006 | 0.018 | 0.035 | 0.05 | 0.06 | 0.07 | 0.095 | 0.12 |
| S1.1.4 | (Pre-)Finishing | 20 | 0.02xD | 0.02xD | 0.002 | 0.004 | 0.011 | 0.02 | 0.03 | 0.035 | 0.045 | 0.06 | 0.075 |
| S1.1.4 | Fine finishing | 20 | 0.01xD | 0.01xD | 0.001 | 0.002 | 0.006 | 0.015 | 0.015 | 0.02 | 0.025 | 0.035 | 0.04 |
fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.
Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 625.
One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.
Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.
| Material group | Vc (m/min) | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 40 | 0.1 | 0.2 | 0.25 | 0.45 | 0.6 | 0.7 | 0.75 | 0.8 | 0.85 | 0.95 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 40 | 0.1 | 0.2 | 0.25 | 0.45 | 0.6 | 0.7 | 0.75 | 0.8 | 0.85 | 0.95 |
f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.
| Material group | Vc (m/min) | f Ø 14 | f Ø 16 | f Ø 18 | f Ø 20 | f Ø 22 | f Ø 24 | f Ø 28 | f Ø 32 | f Ø 38 | f Ø 42 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 40 | 0.8 | 0.85 | 0.9 | 0.95 | 1 | 1 | 1.1 | 1.15 | 1.25 | 1.3 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 40 | 0.8 | 0.85 | 0.9 | 0.95 | 1 | 1 | 1.1 | 1.15 | 1.25 | 1.3 |
f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.
| Material group | Vc (m/min) | f Ø 22 | f Ø 26 | f Ø 30 | f Ø 35 | f Ø 40 |
|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 20 | 0.5 | 0.55 | 0.6 | 0.65 | 0.65 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 20 | 0.5 | 0.55 | 0.6 | 0.65 | 0.65 |
f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.
| Material group | Vc (m/min) | f Ø 40 | f Ø 45 | f Ø 50 | f Ø 55 | f Ø 60 | f Ø 65 | f Ø 70 | f Ø 75 | f Ø 80 |
|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 20 | 0.65 | 0.7 | 0.75 | 0.75 | 0.8 | 0.8 | 0.85 | 0.85 | 0.9 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 20 | 0.65 | 0.7 | 0.75 | 0.75 | 0.8 | 0.8 | 0.85 | 0.85 | 0.9 |
f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 6 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 6 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 10 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 10 | 0.02 | 0.05 | 0.1 | 0.1 | 0.2 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.
| Material group | Vc (m/min) | f Ø 1 | f Ø 2 | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 14 | f Ø 18 | f Ø 22 | f Ø 30 | f Ø 40 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 6 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 6 | 0.02 | 0.05 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 | 0.4 |
f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.
| Material group | Vc (m/min) | f Ø 3 | f Ø 4 | f Ø 6 | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 |
|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 6 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 6 | 0.05 | 0.1 | 0.15 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 |
f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.
| Material group | Vc (m/min) | f Ø 8 | f Ø 10 | f Ø 12 | f Ø 14 | f Ø 16 | f Ø 20 | f Ø 25 | f Ø 30 |
|---|---|---|---|---|---|---|---|---|---|
| S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB | 6 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
| S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB | 6 | 0.2 | 0.25 | 0.25 | 0.25 | 0.3 | 0.3 | 0.35 | 0.35 |
f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.
Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 625.
Tough fine-grain PVD carbide for general work; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718, which runs in a separate, much higher speed regime.
The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO S grade list and in the grade chart.
EN NiCr22Mo9Nb (Alloy 625), Werkstoffnummer 2.4856, US UNS N06625. The full table, with the nearest-match flags, is on the Inconel 625 / 2.4856 cross-reference page.
Gummier and stickier than 718 rather than harder: expect built-up edge and depth-of-cut notching. Sharp positive S-geometry and steady feed beat brute toughness.
Are you overpaying on your Inconel 625 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
The published starting band for the S20 Nickel superalloys (Inconel 718) sub-group is 20–45 m/min (65–150 sfm) at 0.10–0.25 mm/rev (.004–.010 ipr). It is a starting band for the whole sub-group, not a value tuned to Inconel 625, so confirm on a sample part and adjust for condition, tool and rigidity.
Tough fine-grain PVD carbide for general work; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718, which runs in a separate, much higher speed regime. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.
EN NiCr22Mo9Nb (Alloy 625) (Werkstoffnummer 2.4856); US: UNS N06625; JIS: none listed. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.
The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.