CUTTINGTOOLS / AI
Find equivalents
MACHINING DATA · S NICKEL SUPERALLOY

Inconel 718 machining data: cutting speed, feed and carbide grade to start with.

Starting cutting speed in m/min and sfm, feed in mm/rev and ipr, the carbide grade class and the setup by operation for Inconel 718 (NiCr19NbMo). The numbers are the published S20 Nickel superalloys (Inconel 718) sub-group starting band; the designations are on the cross-reference page.

ISO S · Superalloys and titanium S20 sub-group m/min + sfm · mm/rev + ipr Free, no signup

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

01 · AT A GLANCE

Inconel 718: group, sub-group and condition

ItemValue
ISO 513 groupS Superalloys and titanium
Sub-groupS20 Nickel superalloys (Inconel 718)
Sub-group hardness / condition280–380 HB
CategoryNickel superalloy
EN / WerkstoffnummerNiCr19NbMo (Alloy 718) · 2.4668

Hardness is the range published for the whole S20 Nickel superalloys (Inconel 718) sub-group on our material guide; the delivery condition of your Inconel 718 may sit anywhere inside it or outside it.

02 · STARTING CUTTING DATA

Cutting speed and feed for Inconel 718

ConditionVc m/minVc sfmFeed mm/revFeed ipr
S20 Nickel superalloys (Inconel 718), 280–380 HB20–4565–1500.10–0.25.004–.010

Sub-group starting values for carbide inserts, from S20 Nickel superalloys (Inconel 718). They describe the whole sub-group and are not tuned to Inconel 718. sfm and ipr are converted from the metric values (1 m/min = 3.281 sfm, 25.4 mm = 1 in). The published band is per sub-group, not per operation; the table below gives the setup by operation. Convert Vc to spindle speed with the speeds & feeds calculator, and see the speeds & feeds guide for the ISO S group range.

Setup by operation

OperationGeometryCoating familyCoolantFirst check
RoughingPositive but strong, honed edge; round or large-nose insert spreads heatTough fine-grain PVD carbide; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718High-pressure coolant essentialDepth-of-cut notch wear: vary DOC between passes
FinishingPositive, honed edge; avoid fragile sharp cornersTough fine-grain PVD carbideHigh-pressure coolant essentialRapid cratering and heat: coolant to the edge, hold Vc in band
Interrupted cutStrong honed edge, round insert where possibleTough fine-grain PVD carbideHigh-pressure coolant essentialEdge chipping or built-up edge: sharp honed positive edge
Low rigidity / thin wallPositive but strong edge; keep the tool movingTough fine-grain PVD carbideHigh-pressure coolant essentialWork-hardened skin: keep DOC above the hardened layer

Setup rows are the selection table of the S20 Nickel superalloys (Inconel 718) guide. They carry no speeds, so they do not change the starting band above.

Same sub-group, same starting band: Inconel 625 · Waspaloy

02b · DRILLING

Drilling Inconel 718 with solid carbide: published starting values

One manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.

S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB (46 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no15 / 0.06------398
Art. 2469
coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26406
Art. 2471
Solid carbide drills, coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0625 / 0.10525 / 0.1325 / 0.15525 / 0.17525 / 0.2225 / 0.26403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0625 / 0.10525 / 0.1325 / 0.15525 / 0.17525 / 0.2225 / 0.26403
Art. 2474
Solid carbide drills, coating FIRE
no25 / 0.0525 / 0.0825 / 0.125 / 0.1225 / 0.1425 / 0.17525 / 0.205404
Art. 2477
coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26406
Art. 2479
Solid carbide drills, coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0625 / 0.10525 / 0.1325 / 0.15525 / 0.17525 / 0.2225 / 0.26403
Art. 2719
Solid carbide drills, coating FIRE
no25 / 0.0525 / 0.0825 / 0.125 / 0.1225 / 0.1425 / 0.17525 / 0.205404
Art. 2996
Solid carbide drills, coating FIRE
no25 / 0.0525 / 0.0825 / 0.125 / 0.1225 / 0.1425 / 0.17525 / 0.205404
Art. 4044
coating FIRE
yes35 / 0.0535 / 0.0835 / 0.135 / 0.1235 / 0.1435 / 0.17535 / 0.205408
Art. 4045
coating FIRE
yes35 / 0.0535 / 0.0835 / 0.135 / 0.1235 / 0.1435 / 0.17535 / 0.205408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26412
Art. 5499
Solid carbide drills, coating FIRE
yes35 / 0.0535 / 0.0835 / 0.135 / 0.1235 / 0.1435 / 0.17535 / 0.205413
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26407
Art. 5651
Solid carbide drills, coating FIRE
no25 / 0.0525 / 0.0825 / 0.125 / 0.1225 / 0.1425 / 0.17525 / 0.205404
Art. 6023
coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26406
Art. 6025
coating TiAlN nanoA
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26414
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no25 / 0.0625 / 0.10525 / 0.1325 / 0.15525 / 0.17525 / 0.2225 / 0.26403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes30 / 0.036------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no15 / 0.036------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes30 / 0.036------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes30 / 0.036------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no25 / 0.06------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes45 / 0.06------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes45 / 0.06------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes45 / 0.06------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes45 / 0.06------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes35 / 0.045------397
Art. 6498
coating FIRE
yes35 / 0.0635 / 0.10535 / 0.1335 / 0.15535 / 0.17535 / 0.2235 / 0.26412
Art. 6499
coating FIRE
yes35 / 0.0535 / 0.0835 / 0.135 / 0.1235 / 0.1435 / 0.17535 / 0.205413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes35 / 0.0435 / 0.06535 / 0.0835 / 0.09535 / 0.1135 / 0.135-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes35 / 0.0435 / 0.06535 / 0.0835 / 0.09535 / 0.1135 / 0.135-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes35 / 0.0435 / 0.06535 / 0.0835 / 0.09535 / 0.1135 / 0.135-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes35 / 0.0435 / 0.06535 / 0.0835 / 0.09535 / 0.11--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes35 / 0.0435 / 0.06535 / 0.0835 / 0.095---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes25 / 0.0525 / 0.0825 / 0.125 / 0.1225 / 0.1425 / 0.17525 / 0.205402
Art. 8511
coating TiAlN nanoA
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26414
Art. 8520
coating Signum
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26410
Art. 8521
coating Signum
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26410
Art. 8522
coating Signum
yes40 / 0.0540 / 0.0840 / 0.140 / 0.1240 / 0.1440 / 0.17540 / 0.205411
Art. 8524
coating Signum
no25 / 0.0625 / 0.10525 / 0.1325 / 0.15525 / 0.17525 / 0.2225 / 0.26405
Art. 8611
coating TiAlN nanoA
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26414
Art. 8620
coating Signum
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26410
Art. 8621
coating Signum
yes40 / 0.0640 / 0.10540 / 0.1340 / 0.15540 / 0.17540 / 0.2240 / 0.26410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 410, 411, 412, 413, 414, 426, 427, 428, 429, 430).

S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB (46 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no10 / 0.042------398
Art. 2469
coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18406
Art. 2471
Solid carbide drills, coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no15 / 0.04515 / 0.07515 / 0.0915 / 0.10515 / 0.12515 / 0.15515 / 0.18403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no15 / 0.04515 / 0.07515 / 0.0915 / 0.10515 / 0.12515 / 0.15515 / 0.18403
Art. 2474
Solid carbide drills, coating FIRE
no15 / 0.03515 / 0.05515 / 0.0715 / 0.08515 / 0.09515 / 0.1215 / 0.145404
Art. 2477
coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18406
Art. 2479
Solid carbide drills, coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no15 / 0.04515 / 0.07515 / 0.0915 / 0.10515 / 0.12515 / 0.15515 / 0.18403
Art. 2719
Solid carbide drills, coating FIRE
no15 / 0.03515 / 0.05515 / 0.0715 / 0.08515 / 0.09515 / 0.1215 / 0.145404
Art. 2996
Solid carbide drills, coating FIRE
no15 / 0.03515 / 0.05515 / 0.0715 / 0.08515 / 0.09515 / 0.1215 / 0.145404
Art. 4044
coating FIRE
yes20 / 0.03520 / 0.05520 / 0.0720 / 0.08520 / 0.09520 / 0.1220 / 0.145408
Art. 4045
coating FIRE
yes20 / 0.03520 / 0.05520 / 0.0720 / 0.08520 / 0.09520 / 0.1220 / 0.145408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18412
Art. 5499
Solid carbide drills, coating FIRE
yes20 / 0.03520 / 0.05520 / 0.0720 / 0.08520 / 0.09520 / 0.1220 / 0.145413
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18407
Art. 5651
Solid carbide drills, coating FIRE
no15 / 0.03515 / 0.05515 / 0.0715 / 0.08515 / 0.09515 / 0.1215 / 0.145404
Art. 6023
coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18406
Art. 6025
coating TiAlN nanoA
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18414
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no15 / 0.04515 / 0.07515 / 0.0915 / 0.10515 / 0.12515 / 0.15515 / 0.18403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes20 / 0.025------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no10 / 0.025------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes20 / 0.025------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes20 / 0.025------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no15 / 0.042------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes30 / 0.042------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes30 / 0.042------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes30 / 0.042------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes30 / 0.042------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes20 / 0.032------397
Art. 6498
coating FIRE
yes20 / 0.04520 / 0.07520 / 0.0920 / 0.10520 / 0.12520 / 0.15520 / 0.18412
Art. 6499
coating FIRE
yes20 / 0.03520 / 0.05520 / 0.0720 / 0.08520 / 0.09520 / 0.1220 / 0.145413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.095-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.095-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.07520 / 0.095-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes20 / 0.02520 / 0.04520 / 0.05520 / 0.06520 / 0.075--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes20 / 0.02520 / 0.04520 / 0.05520 / 0.065---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes15 / 0.03515 / 0.05515 / 0.0715 / 0.08515 / 0.09515 / 0.1215 / 0.145402
Art. 8511
coating TiAlN nanoA
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18414
Art. 8520
coating Signum
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18410
Art. 8521
coating Signum
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18410
Art. 8522
coating Signum
yes25 / 0.03525 / 0.05525 / 0.0725 / 0.08525 / 0.09525 / 0.1225 / 0.145411
Art. 8524
coating Signum
no15 / 0.04515 / 0.07515 / 0.0915 / 0.10515 / 0.12515 / 0.15515 / 0.18405
Art. 8611
coating TiAlN nanoA
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18414
Art. 8620
coating Signum
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18410
Art. 8621
coating Signum
yes25 / 0.04525 / 0.07525 / 0.0925 / 0.10525 / 0.12525 / 0.15525 / 0.18410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 410, 411, 412, 413, 414, 426, 427, 428, 429, 430).

Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 718. Start here, then adjust to your machine, setup rigidity, hole depth and coolant. Turn Vc and f into rpm and feed rate with the drilling calculator.

02c · MILLING

Milling Inconel 718: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
S1.1.3HPC Roughing7 Speed303xD0.08xD0.030.040.0550.070.0850.110.140.14
S1.1.3HSC Roughing7 Speed303xD0.05xD0.030.040.0550.070.0850.110.140.14
S1.1.3Finishing7 Speed303xD0.01xD0.010.0150.020.0250.030.040.050.05
S1.1.4HPC Roughing7 Speed203xD0.08xD0.0250.040.0550.0650.080.1050.130.13
S1.1.4HSC Roughing7 Speed203xD0.05xD0.0250.040.0550.0650.080.1050.130.13
S1.1.4Finishing7 Speed203xD0.01xD0.010.0150.020.0250.030.040.050.05

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
S1.1.3Roughing400.06xD0.2xD0.0080.0160.0310.0470.0650.0950.1250.1550.19
S1.1.3(Pre-)Finishing350.02xD0.05xD0.0080.0160.0310.0470.0650.0950.1250.1550.19
S1.1.3Fine finishing350.01xD0.02xD0.0070.0140.0270.0410.0550.080.110.1350.165
S1.1.4Roughing300.06xD0.2xD0.0070.0150.030.0450.060.090.120.150.18
S1.1.4(Pre-)Finishing250.02xD0.05xD0.0070.0150.030.0450.060.090.120.150.18
S1.1.4Fine finishing250.01xD0.02xD0.0070.0130.0260.0390.050.080.1050.130.155

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
S1.1.3Roughing300.04xD0.25xD0.0070.0130.0270.040.0550.080.1050.1350.16
S1.1.3(Pre-)Finishing250.03xD0.2xD0.0050.010.0190.0290.040.060.080.0950.115
S1.1.3Fine finishing300.01xD0.1xD0.0070.0140.0280.0420.0550.0850.1150.140.17
S1.1.4Roughing250.04xD0.25xD0.0060.0130.0250.0380.050.0750.10.1250.15
S1.1.4(Pre-)Finishing200.03xD0.2xD0.0050.0090.0180.0280.0350.0550.0750.090.11
S1.1.4Fine finishing200.01xD0.1xD0.0070.0130.0270.040.0550.080.1050.1350.16

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
S1.1.3Roughing300.1xD0.1xD0.0030.0060.0190.040.050.0650.0750.10.125
S1.1.3(Pre-)Finishing250.02xD0.02xD0.0020.0040.0120.0250.030.040.0450.060.075
S1.1.3Fine finishing250.01xD0.01xD0.0010.0020.0070.0150.020.020.0250.0350.045
S1.1.4Roughing250.1xD0.1xD0.0030.0060.0180.0350.050.060.070.0950.12
S1.1.4(Pre-)Finishing200.02xD0.02xD0.0020.0040.0110.020.030.0350.0450.060.075
S1.1.4Fine finishing200.01xD0.01xD0.0010.0020.0060.0150.0150.020.0250.0350.04

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 718.

02e · REAMING

Reaming Inconel 718: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

Scope: Pick the table for your condition: solution-annealed material is near S1.1.3 (250 HB). Aged Inconel 718 (around 40 HRC) is at or above S1.1.4 (350 HB), so start at the low end.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB400.10.20.250.450.60.70.750.80.850.95
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB400.10.20.250.450.60.70.750.80.850.95

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB400.80.850.90.95111.11.151.251.3
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB400.80.850.90.95111.11.151.251.3

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB200.50.550.60.650.65
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB200.50.550.60.650.65

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB200.650.70.750.750.80.80.850.850.9
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB200.650.70.750.750.80.80.850.850.9

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB60.020.050.10.10.20.250.30.30.350.350.4
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB60.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB100.020.050.10.10.20.250.30.30.350.350.4
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB100.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB60.020.050.050.10.150.20.250.250.30.350.350.4
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB60.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB60.050.10.150.20.250.250.250.3
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB60.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
S1.1.3: Heat-resistant alloys, Ni- or Co-based, annealed, 250 HB60.20.250.250.250.30.30.350.35
S1.1.4: Heat-resistant alloys, Ni- or Co-based, hardened, 350 HB60.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

Values are for the catalogue material group(s) shown, which cover the S20 Nickel superalloys (Inconel 718) sub-group; they are not tuned to Inconel 718.

03 · CARBIDE GRADES

Carbide grade class for Inconel 718

Tough fine-grain PVD carbide for general work; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718, which runs in a separate, much higher speed regime.

The P, M, K, N, S or H number inside a grade range describes what the grade is built for, not the workpiece sub-group number, and the two scales must not be matched to each other. We name no single grade here: none of our published sources ties a named grade to this alloy. Pick by ISO class, then compare what the makers publish on the ISO S grade list and in the grade chart.

04 · DESIGNATIONS

Inconel 718 in EN, US and JIS terms

EN NiCr19NbMo (Alloy 718), Werkstoffnummer 2.4668, US UNS N07718. The full table, with the nearest-match flags, is on the Inconel 718 / 2.4668 cross-reference page.

05 · NOTES

How NiCr19NbMo behaves in the cut

The reference S-group nightmare: work-hardening, abrasive carbides, red-hot chips at Vc 15-50. Aged 718 is harder on tools than solution-annealed; ceramic roughing changes the game where the setup allows it.

Cost check · free · brand-neutral

Are you overpaying on your Inconel 718 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

06 · FAQ

Common questions

What cutting speed should I start with for Inconel 718?

The published starting band for the S20 Nickel superalloys (Inconel 718) sub-group is 20–45 m/min (65–150 sfm) at 0.10–0.25 mm/rev (.004–.010 ipr). It is a starting band for the whole sub-group, not a value tuned to Inconel 718, so confirm on a sample part and adjust for condition, tool and rigidity.

Which carbide grade should I use for Inconel 718?

Tough fine-grain PVD carbide for general work; whisker-reinforced or SiAlON ceramic for high-speed roughing of aged 718, which runs in a separate, much higher speed regime. Pick the grade by ISO class rather than by brand name, then confirm the exact grade for your condition. We name no single grade here because none of our published sources ties a named grade to this alloy.

What is Inconel 718 called in EN, US and JIS standards?

EN NiCr19NbMo (Alloy 718) (Werkstoffnummer 2.4668); US: UNS N07718; JIS: none listed. Entries marked nearest are the closest commonly-cited counterpart, not a same-composition equivalent.

NEXT

Starting band found. Now the exact grade.

The advisor compares what the makers publish for your material and operation and shows the source behind each answer, or tells you it could not verify.