CUTTINGTOOLS / AI
Find equivalents
Advisor / Tool wear / Plastic deformation
Tool wear modes · ISO 3685

Plastic deformation: what it looks like, why it happens, how to fix it

The edge bulges or slumps; a bright, rounded land forms that resembles flank wear, the clearance collapses and the edge then fails quickly. Heat plus pressure exceed the hot hardness of the carbide substrate. At roughly 600 to 800 degrees C at the tool-chip interface the cutting wedge creeps and the edge sinks (plastic lowering). This is not wear: no material is removed at first.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Plastic deformation at a glance
What you seeMechanismFirst fixMost affected
The edge bulges or slumps; a bright, rounded land forms that resembles flank wear, the clearance collapses and the edge then fails quickly.Heat plus pressure exceed the hot hardness of the carbide substrate.Reduce Vc and feed, and use a substrate with higher hot hardness; improve cooling at the edge.ISO K (cast iron), ISO H (hardened steel), ISO M (stainless steel)

Why it happens

How to measure and judge it

Look for a rounded, shiny edge and a bulge below the cut rather than a flat, matte land. If the shop can measure both radial wear and the flank land, a ratio that drifts over tool life indicates creep; with pure abrasion that ratio stays constant.

Fixes, in the order to try them

  1. Reduce Vc first, then feed.
  2. Choose a grade with higher hot hardness (less cobalt, a lower number in the ISO group).
  3. Keep the clearance angle as small as the setup allows: extra relief removes material that supports the edge and makes it worse.
  4. Use a chipbreaker rake or an edge chamfer that shortens chip contact and supports the edge.

Likely causes and fixes

Each pairing below is listed under this symptom by at least two independent tool manufacturers in their published troubleshooting guides. Where the makers disagree we leave the item out.

Likely causeFixListed by
Cutting temperature and pressure too highReduce cutting speed and feedSandvik Coromant, ISCAR, Seco Tools
The binder softens because the grade is too soft for the heat loadChoose a harder, more heat-resistant gradeSandvik Coromant, ISCAR, Seco Tools
Too little cooling at the edgeImprove coolant supplySandvik Coromant, ISCAR, Seco Tools

Guides: Sandvik Coromant, Troubleshooting turning · ISCAR, ISO Turn Inserts Wear Troubleshooting · Seco Tools, Tool wear patterns: how to recognize and optimize them

Do not confuse it with

It looks like flank wear, but the fix is opposite: a "harder, more wear-resistant" grade does not help if the wedge is creeping. See flank wear and plastic lowering in detail.

Other wear modes

Flank wear · Crater wear · Notch wear · Built-up edge (BUE) · Thermal cracking · Edge chipping and fracture · All eight failure modes in one table · Mechanisms in depth

Cost check · free · brand-neutral

Are you overpaying on your inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

Frequently asked questions

What is plastic deformation on an insert?

It is the cutting edge sinking or bulging under high temperature and pressure because the carbide substrate creeps. It is not abrasive wear, and it usually ends in a fast collapse of the edge.

How do you stop plastic deformation of the cutting edge?

Lower the cutting speed and feed, use a substrate with higher hot hardness, keep the clearance angle small and use a geometry or edge preparation that supports the edge.