Edge chipping and fracture: what it looks like, why it happens, how to fix it
Small irregular fractures along the cutting edge with an erratic finish (chipping), or gross breakage where the edge or nose is gone (fracture). Mechanical or thermal shock larger than the edge can carry: interrupted cuts, built-up edge breaking away and pulling carbide with it, vibration, or a feed and depth of cut too heavy for the edge.
| What you see | Mechanism | First fix | Most affected |
|---|---|---|---|
| Small irregular fractures along the cutting edge with an erratic finish (chipping), or gross breakage where the edge or nose is gone (fracture). | Mechanical or thermal shock larger than the edge can carry: interrupted cuts, built-up edge breaking away and pulling carbide with it, vibration, or a feed and depth of cut too heavy for the edge.. | Use a tougher grade and a stronger edge preparation (hone or chamfer), and stiffen the setup. | ISO M (stainless steel), ISO S (superalloys and titanium), ISO H (hardened steel), ISO K (cast iron) |
Why it happens
- Grade too brittle for the cut: a very wear-resistant grade in an interrupted or unstable cut chips instead of wearing.
- Built-up edge breaking off takes small pieces of the edge with it.
- Instability: long overhang, weak clamping or thin-walled parts turn every load swing into an impact. See boring bar overhang and chatter.
How to measure and judge it
Chipping is judged by the size of the chips against the feed: chips larger than the feed per revolution mean the edge is too weak for the load. Fracture of the nose usually follows unchecked chipping, crater wear or excessive feed.
Fixes, in the order to try them
- Choose a tougher grade (a higher number in the same ISO group).
- Use a stronger edge preparation: hone or T-land chamfer.
- Reduce feed at entry and exit, and the feed and depth of cut overall if the nose is breaking.
- Shorten overhang, check clamping and remove vibration before re-cutting.
Likely causes and fixes
Each pairing below is listed under this symptom by at least two independent tool manufacturers in their published troubleshooting guides. Where the makers disagree we leave the item out.
| Likely cause | Fix | Listed by |
|---|---|---|
| Vibration and an unstable set-up | Make the set-up more rigid and stable | Sandvik Coromant, Seco Tools |
| Edge or grade too brittle for the load | Choose a tougher grade and a stronger edge | Sandvik Coromant, ISCAR, Seco Tools, Tungaloy |
| A built-up edge forms, then tears out edge material | Increase cutting speed (see built-up edge) | ISCAR, Sandvik Coromant, Seco Tools |
| Impact at entry or exit of the cut | Reduce feed at the start of the cut | ISCAR, Sandvik Coromant, Seco Tools |
| Geometry too weak for the application | Choose a stronger geometry | Sandvik Coromant, ISCAR |
Guides: Sandvik Coromant, Troubleshooting turning · Seco Tools, Tool wear patterns: how to recognize and optimize them · ISCAR, ISO Turn Inserts Wear Troubleshooting · Tungaloy, Troubleshooting in turning (Users Guide 2023-2024, L007) · Sandvik Coromant, Troubleshooting milling
Do not confuse it with
Cracks running across the edge before pieces fall out mean thermal fatigue rather than mechanical overload. See thermal cracking.
Other wear modes
Flank wear · Crater wear · Notch wear · Built-up edge (BUE) · Plastic deformation · Thermal cracking · All eight failure modes in one table · Mechanisms in depth
Are you overpaying on your inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works
Frequently asked questions
Why does my insert chip?
Inserts chip when the mechanical or thermal shock is larger than the edge can carry: an interrupted cut, built-up edge breaking away, vibration or a grade that is too brittle for the job.
How do you stop inserts from breaking?
Use a tougher grade and a stronger edge preparation, reduce feed and depth of cut, and check rigidity, clamping and overhang before cutting again.