Carbide grade · ISCAR · ISO P/M/K/S
ISCAR IC908
IC908 is a ISCAR carbide insert grade (PVD TiAlN), applied in the ISO P/M/K/S areas. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by Sandvik. 2 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 222 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- ISCAR
- Coating / substrate
- PVD TiAlN
- ISO application area
- P — steel · M — stainless steel · K — cast iron · S — superalloys & titanium
- Application range (catalog)
- P20 · K20
- Used in
- 1 insert designation in this reference
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- Sandvik GC1125 ISO P20 S20 S25 · 1 chart (Ingersoll)
- TaeguTec TT9080 ISO K20 P25 S20 S25 · 2 charts (Korloy, TaeguTec)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi VP15TF ISO K20 M10 M30 M35 P20 S20 S25 · not verified · carbide
- Tungaloy AH725 ISO M10 M30 M35 P20 S20 S25 · not verified
- Kyocera PR1225 ISO M10 M30 M35 P20 P25 · not verified · carbide
- Sumitomo AC1030U ISO K20 M30 M35 P20 P25 · not verified · carbide
- Seco CP500 ISO M30 M35 P25 S20 S25 · not verified
152 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Kennametal KC735M ISO M30 · not verified
- Mitsubishi MP7030 ISO M30 · not verified
- Mitsubishi MP7130 ISO M30 · not verified
- Sandvik GC1040 ISO M30 · not verified
- Sandvik GC2030 ISO M30 · not verified
26 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kyocera PV720 ISO P20 · not verified · cermet
- Kyocera TN620 ISO P20 · not verified · cermet
- Mitsubishi MC7015 ISO M10 · not verified
- Mitsubishi NX2525 ISO P20 · not verified · cermet
- Sumitomo AC6020M ISO M10 · not verified
29 more not shown.
The best-evidenced alternative to ISCAR IC908 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check ISCAR IC908 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
| Brand | Grade | Coating | Shared designations |
|---|---|---|---|
| Sandvik | GC3040 | CVD | WCMX050308 |
Compare IC908 side by side
Insert designations using IC908
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| WCMX050308 | 80° Trigon · 0° clearance · 5mm IC · indexable drill insert | WCMX 050308 IC908 | P20 · K20 |
Frequently asked questions
What is ISCAR IC908?
IC908 is a ISCAR carbide insert grade (PVD TiAlN), applied in the ISO P/M/K/S areas, used in 1 insert designation in this reference.
Which grades are direct peers of IC908?
2 grades from other makers are listed in the same row of a manufacturer comparison chart as IC908: Sandvik GC1125, TaeguTec TT9080. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your IC908 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where IC908 is used: designations and materials