CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO P/M/S

ISCAR IC28

IC28 is a ISCAR carbide insert grade (Uncoated carbide), applied in the ISO P/M/S areas. In this cross-reference it appears on 4 insert designations; the same insert geometry is also made by Kennametal, Sandvik, Seco, Tungaloy, Walter. No manufacturer chart on file lists a direct peer for it. 140 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
Uncoated carbide
ISO application area
P — steel · M — stainless steel · S — superalloys & titanium
Application range (catalog)
N05–N15 · N05–N20
Used in
4 insert designations in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Kennametal KC735M ISO M30 P30 P40 · not verified
  • Kyocera PR1535 ISO M30 P30 S20 · not verified · carbide
  • Mitsubishi VP15TF ISO M30 P30 S20 · not verified · carbide
  • TaeguTec TT8020 ISO M30 P30 P40 · not verified
  • Tungaloy AH725 ISO M30 P30 S20 · not verified

118 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

12 more not shown.

Check IC28 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC28 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC28 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
Kennametal KCU25 PVD AlTiN CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404
Sandvik H13A Uncoated carbide CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404
Seco H15F Uncoated fine-grain carbide VCGT160404
Tungaloy T1010 Uncoated CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404
Walter WNK10 Uncoated sharp CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404

Insert designations using IC28

DesignationGeometryCatalog codeApplication
CCGT09T304 80° Diamond · 7° clearance · 0.4mm Rε · aluminium geometry CCGT 09T304 IC28 N05–N20
DCGT11T304 55° Diamond · 7° clearance · 0.4mm Rε · positive aluminium DCGT 11T304 IC28 N05–N20
TCGT16T304 60° Triangle · 7° clearance · 0.4mm Rε · aluminium geometry TCGT 16T304 IC28 N05–N15
VCGT160404 35° Rhombic · 7° clearance · 0.4mm Rε · positive aluminium VCGT 160404 IC28 N05–N20

Frequently asked questions

What is ISCAR IC28?

IC28 is a ISCAR carbide insert grade (Uncoated carbide), applied in the ISO P/M/S areas, used in 4 insert designations in this reference.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC28
Cutting data for your material, when IC28 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC28 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC28 is used: designations and materials