CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO P

ISCAR IC8150

IC8150 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 11 insert designations; the same insert geometry is also made by Kennametal, Mitsubishi, Sandvik, Seco, Tungaloy, Walter. 3 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 40 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
SUMO TEC® CVD Al₂O₃
ISO application area
P — steel
Application range (catalog)
P10–P20
Used in
11 insert designations in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Walter WPP10S ISO P15 · 2+ independent charts (Korloy, Tungaloy)
  • Sandvik GC4315 ISO P15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Sandvik GC4415 ISO P15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • MOLDINO HG8010 ISO P05 P15 · not verified
  • Mitsubishi MC6115 ISO P05 P15 · not verified
  • Sumitomo AC8015P ISO P05 P15 · not verified
  • Kennametal KCP05 ISO P05 · not verified
  • Kyocera CA510 ISO P05 · not verified

35 more not shown.

Check IC8150 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC8150 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC8150 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Insert designations using IC8150

DesignationGeometryCatalog codeApplication
CCMT09T304 80° Diamond · 7° clearance (positive) · precision finishing CCMT09T304 IC8150 P10–P20
CCMT09T308 80° Diamond · 7° clearance (positive) · 0.8mm Rε CCMT09T308 IC8150 P10–P20
DCMT11T304 55° Diamond · 7° clearance (positive) · 0.4mm Rε DCMT11T304 IC8150 P10–P20
TCMT16T304 60° Triangle · 7° clearance (positive) · 0.4mm Rε TCMT16T304 IC8150 P10–P20
TNMG160404 60° Triangle · 0° clearance · 16mm IC · 0.4mm Rε · semi-finishing TNMG160404 IC8150 P10–P20
VBMT160404 35° Rhombic · 5° clearance · 16mm IC · 0.4mm Rε · tight corner finishing VBMT160404 IC8150 P10–P20
VBMT160408 35° Rhombic · 5° clearance · 16mm IC · 0.8mm Rε VBMT160408 IC8150 P10–P20
WNMG060408 80° Trigon · 0° clearance · 6mm IC · 0.8mm Rε · small diameter turning WNMG060408 IC8150 P10–P20
WNMG080404 80° Trigon · 0° clearance · 8mm IC · 0.4mm Rε (finishing) WNMG080404 IC8150 P10–P20
WNMG080408 80° Trigon · 0° clearance · 8mm IC · 0.8mm Rε WNMG080408 IC8150 P10–P20
WNMG080412 80° Trigon · 0° clearance · 8mm IC · 1.2mm Rε (roughing) WNMG080412 IC8150 P10–P20

Frequently asked questions

What is ISCAR IC8150?

IC8150 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area, used in 11 insert designations in this reference.

Which grades are direct peers of IC8150?

3 grades from other makers are listed in the same row of a manufacturer comparison chart as IC8150: Walter WPP10S, Sandvik GC4315, Sandvik GC4415. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC8150
Cutting data for your material, when IC8150 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC8150 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC8150 is used: designations and materials