CUTTINGTOOLS / AI
Find equivalents

ISO P — Steel · P10

P10 — Alloy steel

Hardness range: 180–280 HB. Part of the ISO P — Steels group. Steel is the most widely machined material. Carbon and alloy steels are the target material for the majority of turning and milling operations. Hardness ranges from ~125 HB (low-carbon) to 350 HB (high-strength structural). CVD-coated carbide (TiCN/Al₂O₃ multilayer) dominates. Positive geometry for finishing, negative for heavy roughing.

Machining alloy steel? Find suitable carbide grades and understand why.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Picking an operation fills in the question. Edit it before you ask: add the tool type, diameter or hardness.

Material profile — P10

ISO designation
P10 (ISO P — Steels)
Material
Alloy steel
Hardness
180–280 HB
ISO group colour
Steel

Tooling guidance — P-group

Group summary
CVD-coated carbide at Vc 200–400 m/min. Positive geometry for finishing, negative for roughing.

Insert selection for 4140 / 4340 alloy steel (annealed) — starting point

ISO application class
P (steel). Match the insert's ISO class, not the brand name. Sandvik, Kennametal, Iscar, Walter, Seco and Mitsubishi each publish a P-class grade — pick by ISO class, then confirm the exact grade for your condition.
Grade & coating
CVD-coated carbide, P15–P25 general; tougher P25–P35 for roughing, P10–P20 for finishing. Annealed alloy steel (4140 / 4340, ~180–280 HB) takes higher speeds than its heat-treated form.
Geometry
Negative geometry is economical for roughing; positive for finishing and low-rigidity work. Use a medium chipbreaker so soft alloy steel does not run long, stringy chips.
Starting parameters
Vc ≈ 200–300 m/min, fn ≈ 0.10–0.40 mm/rev. Typical starting band — confirm in the advisor or on a sample part.

Selection table: alloy steel (4140 / 4340, annealed)

OperationGeometryISO classCoating familyCoolantFirst check
RoughingNegative geometry, economical; medium chipbreakerP25–P35CVD-coated carbidePer processChipbreaker: stringy chips mean feed too low or wrong breaker
FinishingPositive geometry, medium chipbreakerP10–P20CVD-coated carbidePer processBuilt-up edge at low speed: raise Vc, sharper edge
Interrupted cutNegative geometry with a robust edgeP25–P35CVD-coated carbidePer processCrater wear at high speed: ease Vc
Low rigidity / thin wallPositive geometry for low-rigidity workP10–P20CVD-coated carbidePer processFlank wear: balance Vc and grade hardness

Check which of your current inserts are covered →

Drilling Alloy steel with solid carbide: published starting values

These are one manufacturer's published starting values for solid carbide twist drills, read from its catalogue and checked against the source page. Other makers publish different values for their own drills. Pick the row of the drill you actually use; start there, then adjust to your machine, setup rigidity, hole depth and coolant. "Internal coolant ducts" describes the drill's own geometry, not wet or dry machining.

P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB (45 drill families)
Drill familyInternal coolant ductsØ 3 mm
Vc / f
Ø 6 mm
Vc / f
Ø 8 mm
Vc / f
Ø 10 mm
Vc / f
Ø 12 mm
Vc / f
Ø 16 mm
Vc / f
Ø 20 mm
Vc / f
Catalogue page
Art. 701
Micro drills
no30 / 0.087------398
Art. 1946
Solid carbide drills, coating TiAlN
no80 / 0.09580 / 0.16580 / 0.20580 / 0.2480 / 0.27580 / 0.34580 / 0.405434
Art. 2469
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 2471
Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 2472
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2473
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2474
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 2477
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 2479
Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 2480
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 2719
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 2996
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 4044
coating FIRE
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405408
Art. 4045
coating FIRE
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405408
Art. 5498
Ratio drills with coolant ducts, coating FIRE
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55120 / 0.65412
Art. 5499
Solid carbide drills, coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 5525
coating FIRE
yes110 / 0.095110 / 0.165110 / 0.205110 / 0.24110 / 0.275110 / 0.345110 / 0.405409
Art. 5650
RT 100 U Solid carbide drills, coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52407
Art. 5651
Solid carbide drills, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52404
Art. 6023
coating FIRE
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52406
Art. 6026
Ratio drills without coolant ducts, coating FIRE
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52403
Art. 6405
ExclusiveLine Micro drills, coating TiAlN
yes90 / 0.21------392
Art. 6405
ExclusiveLine Micro drills, coating TiAlN SuperA
no80 / 0.21------392
Art. 6408
ExclusiveLine Micro drills, coating TiAlN SuperA
yes90 / 0.12------393
Art. 6412
ExclusiveLine Micro drills, coating TiAlN SuperA
yes90 / 0.12------393
Art. 6487
ExclusiveLine Micro drills, coating Perrox
no80 / 0.21------394
Art. 6488
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.15------395
Art. 6489
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.15------395
Art. 6490
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.09------396
Art. 6491
ExclusiveLine Micro drills, coating Perrox
yes90 / 0.09------396
Art. 6493
ExclusiveLine Micro drills, coating Ferrox
yes90 / 0.105------397
Art. 6498
coating FIRE
yes120 / 0.155120 / 0.26120 / 0.325120 / 0.385120 / 0.44120 / 0.55120 / 0.65412
Art. 6499
coating FIRE
yes110 / 0.155110 / 0.26110 / 0.325110 / 0.385110 / 0.44110 / 0.55110 / 0.65413
Art. 6509
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44-426
Art. 6511
Ratio drills with coolant ducts, coating TiAlN
yes110 / 0.125110 / 0.21110 / 0.26110 / 0.305110 / 0.355110 / 0.44-427
Art. 6512
Ratio drills with coolant ducts, coating TiAlN
yes100 / 0.125100 / 0.21100 / 0.26100 / 0.305100 / 0.355100 / 0.44-428
Art. 6513
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.30590 / 0.355--429
Art. 6514
Ratio drills with coolant ducts, coating TiAlN
yes90 / 0.12590 / 0.2190 / 0.2690 / 0.305---430
Art. 6596
Pilot drills with coolant ducts, coating FIRE
yes80 / 0.0680 / 0.10580 / 0.1380 / 0.15580 / 0.17580 / 0.2280 / 0.26402
Art. 8520
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8521
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8522
coating Signum
yes120 / 0.095120 / 0.165120 / 0.205120 / 0.24120 / 0.275120 / 0.345120 / 0.405411
Art. 8524
coating Signum
no105 / 0.125105 / 0.21105 / 0.26105 / 0.305105 / 0.355105 / 0.44105 / 0.52405
Art. 8620
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410
Art. 8621
coating Signum
yes120 / 0.125120 / 0.21120 / 0.26120 / 0.305120 / 0.355120 / 0.44120 / 0.52410

Vc in m/min, f in mm/rev. Each row is one drill family's own published values; values of different drills are not combined. Article numbers and pages refer to the Gühring general catalogue (cutting data pages 392, 393, 394, 395, 396, 397, 398, 402, 403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413, 426, 427, 428, 429, 430, 434).

Turn Vc and f into rpm and feed rate →

Milling Alloy steel: published starting values by tool and application

One manufacturer's published starting values for solid milling cutters, read from its catalogue, checked against the page image and linked to the tools whose product pages point to that table. Each table belongs to its own tool family: values of different tools are not combined. Use the row for your tool and your application (slotting, roughing, finishing...), keep within the printed ap and ae, then adjust to your machine and setup.

RF 100 Diver (end mill; catalogue page 682)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.1Plunging2301xD1xD0.0150.0250.030.040.0450.060.0750.075
P2.1.1Slotting2301xD1xD0.020.0250.0350.050.060.080.10.1
P2.1.1Roughing3001.5xD0.4xD0.0250.040.050.0650.0750.10.1250.125
P2.1.1Finishing4602xD0.02xD0.020.0350.0450.0550.0650.090.110.11

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Pilot end mills RF 100 P: Art. 6716; Ratio end mills RF 100 Diver: Art. 6736, 6737, 6801, 6802, 6803, 6804; Ratio end mill sets RF 100 Diver: Art. 6754, 6755; Ratio end mills RF 100 Diver (3-fluted): Art. 6797, 6798, 6799, 6800. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %.

RF 100 Speed (end mill; catalogue pages 684, 685)
Material groupApplicationTypeVc (m/min)ap maxae maxfz Ø 4fz Ø 5fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.1HPC RoughingSpeed M2353xD0.15xD0.0350.0550.070.090.1050.1450.180.18
P2.1.1HSC RoughingSpeed M2453xD0.1xD0.0450.0650.0850.110.130.1750.2150.215
P2.1.1HSC FinishingSpeed M2553xD0.01xD0.020.0250.0350.0450.0550.070.090.09

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ratio end mills RF 100 Speed M [Speed M]: Art. 6760, 6761, 6765, 6766; Ratio end mill sets RF 100 Speed M [Speed M]: Art. 6778, 6780; Ratio end mills RF 100 5 Speed [5 Speed]: Art. 6856, 6857, 6858, 6859, 6860, 6861; Ratio end mills RF 100 7 Speed [7 Speed]: Art. 6864, 6865; Ratio end mills RF 100 Speed P [Speed P]: Art. 6958, 6959, 6960, 6961. Printed correction factors: ap roughing > 1.5xD vc -25 % fz -25 %; medium length tools vc -40 % fz -40 %; extra length tools vc -60 % fz -55 %; uncoated tools vc -50 % fz -25 %.

G-Mold 65 HF (high-feed; catalogue page 705)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16
P2.1.1Slotting285see ap table1xD0.0310.0620.0920.1250.1850.2450.350.420.56
P2.1.1Roughing275see ap table0.6xD0.0420.0840.1260.170.250.3350.420.5050.67
P2.1.1(Pre-)Finishing285see ap table0.4xD0.0350.070.1050.140.210.280.350.420.56

ap max (mm) by nominal Ø, as printed for this family; pick the row for your material and hardness:

MaterialHardnessØ 1Ø 2Ø 3Ø 4Ø 6Ø 8Ø 10Ø 12Ø 16
Pless than 850 N/mm²0.060.120.180.240.360.480.60.720.96
Pmore than 850 N/mm²0.050.10.150.20.30.40.50.60.8
Mless than 850 N/mm²0.040.080.120.160.240.320.40.480.64
Mmore than 850 N/mm²0.030.070.10.120.180.240.30.360.48
Kless than 240 HB0.060.120.180.240.360.480.60.720.96
Kmore than 240 HB0.050.10.150.20.30.40.50.60.8
STi alloys0.030.070.10.120.180.240.30.360.48
Hless than 55 HRC0.040.080.120.160.240.320.40.480.64
H55-65 HRC0.030.070.10.120.180.240.30.360.48

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: High-feed end mills G-Mold 65 HF: Art. 6814, 6830, 6831. Printed correction factors: medium length tools vc -25 % ap -20 % fz -25 %; extra length tools vc -50 % ap -50 % fz -50 %.

G-Mold 55 B, G-Mold 65 B, GA 200 A, GF 200 (ball nose; catalogue pages 706, 707)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P2.1.1Roughing2850.1xD0.3xD0.010.0190.0390.0580.080.1150.1550.1950.235
P2.1.1(Pre-)Finishing2750.05xD0.1xD0.0120.0240.0480.0720.0950.1450.190.240.29
P2.1.1Fine finishing2850.01xD0.02xD0.010.0210.0420.0630.0850.1250.170.210.25

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose end mills G-Mold μ 65 B: Art. 6815, 6816, 6817, 6818, 6819; Ball nose end mills G-Mold 65 B: Art. 6832, 6833, 6834, 6835, 6836; Ball nose end mills G-Mold 55 B: Art. 6844, 6845, 6846, 6847, 6848, 6849; Ball nose end mills GA 200 A: Art. 6984. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

G-Mold 55 T, G-Mold 65 T (corner radius / torus; catalogue pages 708, 709)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 2fz Ø 3fz Ø 4fz Ø 6fz Ø 8fz Ø 10fz Ø 12
P2.1.1Roughing1950.05xD0.4xD0.0080.0170.0340.0510.070.10.1350.170.2
P2.1.1(Pre-)Finishing2050.03xD0.25xD0.0070.0140.0270.0410.0550.080.110.1350.16
P2.1.1Fine finishing2100.01xD0.15xD0.0070.0150.030.0450.060.090.120.150.18

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Torus end mills G-Mold μ 65 T: Art. 6820, 6821, 6822, 6823, 6824; Torus end mills G-Mold 65 T: Art. 6837, 6838; Torus end mills G-Mold 55 T: Art. 6850, 6851, 6852, 6853, 6854, 6855. Printed correction factors: medium length tools vc -25 % fz -25 %; extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Universal slot drills and end mills with ball nose (ball nose; catalogue pages 710, 711)
Material groupApplicationVc (m/min)ap maxae maxfz Ø 0.5fz Ø 1fz Ø 3fz Ø 6fz Ø 8fz Ø 10fz Ø 12fz Ø 16fz Ø 20
P2.1.1Roughing3350.1xD0.1xD0.0050.010.0290.060.0750.0950.1150.1550.195
P2.1.1(Pre-)Finishing2650.03xD0.03xD0.0030.0060.0180.0350.0450.060.070.0950.12
P2.1.1Fine finishing2650.01xD0.01xD0.0020.0030.010.020.0250.0350.040.0550.065

fz in mm/tooth. ap and ae as printed (xD = times the tool diameter). Tools this table belongs to: Ball nose slot drills XL (2-fluted): Art. 3030; Ball nose end mills XL (4-fluted): Art. 3043; Ball nose slot drills (2-fluted): Art. 3049, 3679; Ball nose end mills (4-fluted): Art. 3050, 3727. Printed correction factors: extra length tools vc -50 % fz -50 %; uncoated tools vc -60 % fz -25 %.

Turn Vc and fz into rpm and feed rate →

Tapping Alloy steel with solid carbide taps: published cutting speeds

One manufacturer's published cutting speeds for solid carbide taps, read from its catalogue and checked against the page image. Each row is one printed column (hole type and coating) and lists the taps whose own product page points to it; values of different columns are not combined. The feed of a tap is its thread pitch, so only Vc is given.

Material groupColumn (hole type, substrate, coating)Vc (m/min)TapsCatalogue page
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HBthrough-holes, VHM, coating TiCN39Taps for ISO metric threads (Art. 942); Taps for ISO metric fine threads (Art. 943); Taps for ISO metric fine threads (Art. 944)966

Reaming Alloy steel: published starting values by reamer family

One manufacturer's published starting values for solid carbide and carbide-tipped reamers, read from its catalogue and checked against the page image, each table linked to the reamers whose product pages point to it. Values of different reamer families are not combined. Use the row for your reamer family, then adjust to your machine, stock allowance and setup.

HR 500 (solid carbide; catalogue page 1040)
Material groupVc (m/min)f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB1800.30.450.61.151.451.751.92.052.152.35

f in mm/rev. Reamers this table belongs to: Art. 1685, Art. 1686, Art. 1675, Art. 1676.

HR 500 T (solid carbide; catalogue page 1041)
Material groupVc (m/min)f Ø 14f Ø 16f Ø 18f Ø 20f Ø 22f Ø 24f Ø 28f Ø 32f Ø 38f Ø 42
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB1802.052.152.252.352.452.552.72.853.053.2

f in mm/rev. Reamers this table belongs to: Art. 1548, Art. 1549.

HR 500 G, Carbide-tipped (carbide-tipped; catalogue page 1044)
Material groupVc (m/min)f Ø 22f Ø 26f Ø 30f Ø 35f Ø 40
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB3011.051.11.21.25

f in mm/rev. Reamers this table belongs to: Art. 1680, Art. 1681.

HR 500 GT, Carbide-tipped (carbide-tipped; catalogue page 1046)
Material groupVc (m/min)f Ø 40f Ø 45f Ø 50f Ø 55f Ø 60f Ø 65f Ø 70f Ø 75f Ø 80
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB301.251.31.351.451.51.551.61.61.65

f in mm/rev. Reamers this table belongs to: Art. 1038, Art. 1039.

NC machine reamers, bright (solid carbide; catalogue page 1048)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB140.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 1449, Art. 1427.

NC machine reamers, TiAlN-nanoA (solid carbide; catalogue page 1049)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB180.020.050.10.10.20.250.30.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 6017, Art. 6018.

Machine reamers (carbide (brazed); catalogue page 1050)
Material groupVc (m/min)f Ø 1f Ø 2f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 14f Ø 18f Ø 22f Ø 30f Ø 40
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB140.020.050.050.10.150.20.250.250.30.350.350.4

f in mm/rev. Reamers this table belongs to: Art. 717, Art. 718, Art. 1408, Art. 1409, Art. 1410, Art. 1411.

Machine reamers (carbide (brazed); catalogue page 1051)
Material groupVc (m/min)f Ø 3f Ø 4f Ø 6f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB160.050.10.150.20.250.250.250.3

f in mm/rev. Reamers this table belongs to: Art. 674, Art. 1407.

Expanding machine reamers (carbide-tipped; catalogue page 1052)
Material groupVc (m/min)f Ø 8f Ø 10f Ø 12f Ø 14f Ø 16f Ø 20f Ø 25f Ø 30
P2.1.1: Low-alloy steel, annealed, Rm 610 N/mm², 180 HB120.20.250.250.250.30.30.350.35

f in mm/rev. Reamers this table belongs to: Art. 749, Art. 740.

4140 / 4340 alloy steel (annealed): what goes wrong, and what to check first

Built-up edge at low speed
Soft alloy steel welds to the edge below the working band. Raise Vc, use a sharper positive edge, and add coolant. See the tool-wear guide.
Long stringy chips / bird-nesting
Feed too low or the wrong chipbreaker. Increase fn or pick a roughing breaker so chips break instead of nesting.
Crater wear at high speed
Heat wears a crater behind the edge. Use a CVD grade and ease Vc.
Flank wear
Normal abrasion that sets tool life. Balance Vc and pick a harder grade for longer runs.

Reference data

Frequently asked questions

What insert grade should I use for 4140 / 4340 alloy steel?

A CVD-coated carbide in the ISO P class, P15–P25. Match the ISO P class across brands rather than the brand name and confirm the exact grade in the advisor.

What cutting speed for annealed alloy steel with carbide?

Roughly Vc 200–300 m/min and fn 0.10–0.40 mm/rev; annealed steel runs faster than its heat-treated form. Treat this as a starting band and confirm on a sample part.

Why do I get long stringy chips on 4140?

Feed too low or the wrong chipbreaker. Increase the feed or choose a roughing breaker so the chips break instead of bird-nesting.

Why is there built-up edge on soft alloy steel?

You are cutting below the working speed band. Raise the cutting speed, use a sharper positive edge, and add coolant.

Get cutting parameters for Alloy steel
The AI advisor maps your specific material condition and operation to a verified insert grade, coating, and Vc/fn range — with live search across the latest tooling catalogs. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your Alloy steel inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from about USD 10 (EUR 9) per grade. How buying works

Grade designations in this group

Each page cross-references the EN, Werkstoffnummer, AISI/UNS and JIS designations for one material, with the ISO machining group it falls in.

Related materials

Grades and designations catalogued at P10