Carbide grade · Sandvik · ISO M/K/N/S
Sandvik H13A
H13A is a Sandvik carbide insert grade (Uncoated carbide), applied in the ISO M/K/N/S areas. In this cross-reference it appears on 4 insert designations; the same insert geometry is also made by ISCAR, Kennametal, Seco, Tungaloy, Walter. 5 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 157 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Sandvik
- Coating / substrate
- Uncoated carbide
- ISO application area
- M — stainless steel · K — cast iron · N — non-ferrous (aluminium, copper) · S — superalloys & titanium
- Application range (catalog)
- N01 · N01–N10
- Used in
- 4 insert designations in this reference
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- ISCAR IC20 ISO K10 K20 · 1 chart (Ingersoll)
- Kennametal KU10 ISO N10 · 1 chart (Ingersoll)
- Seco 890 ISO K10 N10 · 1 chart (Ingersoll)
- Walter WK1 ISO N10 · 1 chart (Ingersoll)
- Tungaloy TH10 ISO K10 · 1 chart (Ingersoll)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi VP15TF ISO K20 S20 · not verified · carbide
- ISCAR IC908 ISO K20 S20 · not verified
- Kyocera PR1210 ISO K10 K20 · not verified
- Sumitomo ACK3000 ISO K10 K20 · not verified
- Sumitomo ACU2500 ISO K10 K20 · not verified
130 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Walter WSM30S ISO S20 · not verified
- Mitsubishi VP20RT ISO K20 · not verified
- Kennametal KC524M ISO K20 · not verified
- Mitsubishi UTi20T ISO K20 · not verified
- Kyocera PR1510 ISO K20 · not verified
6 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Mitsubishi MP8010 ISO K10 · not verified
- NTK CP1 ISO K10 · not verified
- Sumitomo AC4010K ISO K10 · not verified
- Tungaloy T5105 ISO K10 · not verified
- ISCAR IC5005 ISO K10 · not verified
6 more not shown.
The best-evidenced alternative to Sandvik H13A from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Sandvik H13A against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
| Brand | Grade | Coating | Shared designations |
|---|---|---|---|
| ISCAR | IC28 | Uncoated carbide | CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404 |
| Kennametal | KCU25 | PVD AlTiN | CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404 |
| Seco | H15F | Uncoated fine-grain carbide | VCGT160404 |
| Tungaloy | T1010 | Uncoated | CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404 |
| Walter | WNK10 | Uncoated sharp | CCGT09T304, DCGT11T304, TCGT16T304, VCGT160404 |
Compare H13A side by side
Insert designations using H13A
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| CCGT09T304 | 80° Diamond · 7° clearance · 0.4mm Rε · aluminium geometry | CCGT 09 T3 04-AL H13A | N01–N10 |
| DCGT11T304 | 55° Diamond · 7° clearance · 0.4mm Rε · positive aluminium | DCGT 11 T3 04-AL H13A | N01–N10 |
| TCGT16T304 | 60° Triangle · 7° clearance · 0.4mm Rε · aluminium geometry | TCGT 16 T3 04-AL H13A | N01–N10 |
| VCGT160404 | 35° Rhombic · 7° clearance · 0.4mm Rε · positive aluminium | VCGT 16 04 04-AL H13A | N01 |
Frequently asked questions
What is Sandvik H13A?
H13A is a Sandvik carbide insert grade (Uncoated carbide), applied in the ISO M/K/N/S areas, used in 4 insert designations in this reference.
Which grades are direct peers of H13A?
5 grades from other makers are listed in the same row of a manufacturer comparison chart as H13A: ISCAR IC20, Kennametal KU10, Seco 890, Walter WK1, Tungaloy TH10. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your H13A inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where H13A is used: designations and materials