CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Kennametal · ISO P

Kennametal KCP30B

KCP30B is a Kennametal carbide insert grade (KENGold™ CVD), applied in the ISO P area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR, Mitsubishi, Sandvik, Seco, Tungaloy, Walter. No manufacturer chart on file lists a direct peer for it. 86 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Kennametal
Coating / substrate
KENGold™ CVD
ISO application area
P — steel
Application range (catalog)
P30–P40
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • ISCAR IC8350 ISO P30 P35 · not verified
  • Kyocera PR1535 ISO P30 P35 · not verified · carbide
  • Mitsubishi VP20RT ISO P30 P35 · not verified
  • Tungaloy UX30 ISO P30 P35 · not verified
  • Mitsubishi UTi20T ISO P30 P35 · not verified

58 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • Sandvik GC1125 ISO P30 · not verified
  • Sumitomo T2500A ISO P30 · not verified
  • Sumitomo T2500Z ISO P30 · not verified · cermet
  • Tungaloy NS9530 ISO P30 · not verified
  • Kyocera CA025P ISO P30 · not verified

18 more not shown.

Check KCP30B with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Kennametal KCP30B from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Kennametal KCP30B against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
ISCAR IC8350 SUMO TEC® CVD Al₂O₃ CNMG120412
Mitsubishi MC6035 CVD Al₂O₃ CNMG120412
Sandvik GC4335 Inveio® CVD CNMG120412
Seco TP3500 Duratomic® CVD CNMG120412
Tungaloy T9235 CVD TiCN/Al₂O₃ CNMG120412
Walter WPP30S Tiger·tec® Silver CVD CNMG120412

Insert designations using KCP30B

DesignationGeometryCatalog codeApplication
CNMG120412 80° Diamond · 0° clearance · 12mm IC · 1.2mm Rε · heavy roughing CNMG120412 KCP30B P30–P40

Frequently asked questions

What is Kennametal KCP30B?

KCP30B is a Kennametal carbide insert grade (KENGold™ CVD), applied in the ISO P area, used in 1 insert designation in this reference.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about KCP30B
Cutting data for your material, when KCP30B is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your KCP30B inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where KCP30B is used: designations and materials