Carbide grade · Tungaloy · ISO P
Tungaloy T9235
T9235 is a Tungaloy carbide insert grade (CVD TiCN/Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR, Kennametal, Mitsubishi, Sandvik, Seco, Walter. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 88 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Tungaloy
- Coating / substrate
- CVD TiCN/Al₂O₃
- ISO application area
- P — steel
- Application range (catalog)
- P30–P40
- Used in
- 1 insert designation in this reference
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- Sandvik GC4335 ISO P30 P35 P40 · 2 charts (Ingersoll, Tungaloy)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- ISCAR IC8350 ISO P30 P35 · not verified
- ISCAR IC830 ISO P30 P40 · not verified
- Kennametal KC735M ISO P30 P40 · not verified
- Kyocera PR1535 ISO P30 P35 · not verified · carbide
- Mitsubishi VP20RT ISO P30 P35 · not verified
61 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kennametal KCPK30 ISO P30 · not verified
- Sumitomo ACP2000 ISO P30 · not verified
- Mitsubishi VP45N ISO P30 · not verified
- Sandvik GC1125 ISO P30 · not verified
- Sumitomo T2500A ISO P30 · not verified
17 more not shown.
The best-evidenced alternative to Tungaloy T9235 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Tungaloy T9235 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
| Brand | Grade | Coating | Shared designations |
|---|---|---|---|
| ISCAR | IC8350 | SUMO TEC® CVD Al₂O₃ | CNMG120412 |
| Kennametal | KCP30B | KENGold™ CVD | CNMG120412 |
| Mitsubishi | MC6035 | CVD Al₂O₃ | CNMG120412 |
| Sandvik | GC4335 | Inveio® CVD | CNMG120412 |
| Seco | TP3500 | Duratomic® CVD | CNMG120412 |
| Walter | WPP30S | Tiger·tec® Silver CVD | CNMG120412 |
Compare T9235 side by side
Insert designations using T9235
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| CNMG120412 | 80° Diamond · 0° clearance · 12mm IC · 1.2mm Rε · heavy roughing | CNMG120412 T9235 | P30–P40 |
Frequently asked questions
What is Tungaloy T9235?
T9235 is a Tungaloy carbide insert grade (CVD TiCN/Al₂O₃), applied in the ISO P area, used in 1 insert designation in this reference.
Which grades are direct peers of T9235?
1 grade from another maker is listed in the same row of a manufacturer comparison chart as T9235: Sandvik GC4335. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your T9235 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where T9235 is used: designations and materials