CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Tungaloy · ISO M/S

Tungaloy AH8015

AH8015 is a Tungaloy carbide insert grade (PVD AlTiN), applied in the ISO M/S areas. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR, Kennametal. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 70 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Tungaloy
Coating / substrate
PVD AlTiN
ISO application area
M — stainless steel · S — superalloys & titanium
Application range (catalog)
ISO S (HRSA)
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Sandvik GC1115 ISO S10 · 1 chart (Ingersoll)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • ISCAR IC6025 ISO M20 · not verified
  • Kennametal KC525M ISO M20 · not verified
  • Kennametal KCM25B ISO M20 · not verified
  • Kyocera CA6525 ISO M20 · not verified
  • Kyocera PR1225 ISO M20 · not verified · carbide

65 more not shown.

Check AH8015 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Tungaloy AH8015 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Tungaloy AH8015 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
ISCAR IC806 PVD TiAlN (SUMO TEC®) RCMT1204
Kennametal KCU10B PVD AlTiN RCMT1204

Insert designations using AH8015

DesignationGeometryCatalog codeApplication
RCMT1204 Round · 7° clearance · 12mm diameter · 4.76mm thick RCMT1204M0-RS AH8015 ISO S (HRSA)

Frequently asked questions

What is Tungaloy AH8015?

AH8015 is a Tungaloy carbide insert grade (PVD AlTiN), applied in the ISO M/S areas, used in 1 insert designation in this reference.

Which grades are direct peers of AH8015?

1 grade from another maker is listed in the same row of a manufacturer comparison chart as AH8015: Sandvik GC1115. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about AH8015
Cutting data for your material, when AH8015 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your AH8015 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where AH8015 is used: designations and materials